A combination of three resistors R1, R2 and R3 in series is connected across a voltage source V-. The voltage drop across Rq and R3 are 10 V and 36 V, respectively. If the current supplied by the source voltage is 1.4 A and the total power supplied by the source is 70 W, Calculate the following: A. The value of V, and the voltage drop across R2 B. The equivalent resistance across the voltage source, and the values of R1, R2 and R3 C. The power dissipated by each resistor

A combination of three resistors R1, R2 and R3 in series is connected across a voltage source V-. The voltage drop across Rq and R3 are 10 V and 36 V, respectively. If the current supplied by the source voltage is 1.4 A and the total power supplied by the source is 70 W, Calculate the following: A. The value of V, and the voltage drop across R2 B. The equivalent resistance across the voltage source, and the values of R1, R2 and R3 C. The power dissipated by each resistor

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter21: Current And Direct Current Circuits

Section: Chapter Questions

Problem 41P: Three 100- resistors are connected as shown in Figure P21.41 The maximum power that can safely be...

See similar textbooks

Similar questions

For the purpose of measuring the electric resistance of shoes through the body of the wearer standing on a metal ground plate, the American National Standards Institute (ANSI) specifies the circuit shown in Figure P27.14. The potential difference V across the 1.00-M resistor is measured with an ideal voltmeter. (a) Show that the resistance of the footwear is Rshoes=50.0VVV (b) In a medical test, a current through the human body should not exceed 150 A. Can the current delivered by the ANSI-specified circuit exceed 150 A? To decide, consider a person standing barefoot on the ground plate. Figure P27.14
(a) What is the terminal voltage of a large 1.54-V carbon-zinc dry cell used in a physics lab to supply 2.00 A to a circuit if the cell’s internal resistance is 0.100 ? (b) How much electrical power does the cell produce? (c) What power goes to its load?
(a) What is the internal resistance of a voltage source if its terminal potential drops by 2.00 V when the current supplied increases by 5.00 A? (b) Can the emf of the voltage source be found with the information supplied?
Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0 resistor, (b) Find the current in the 3.00-12 resistor.
Three 100- resistors are connected as shown in Figure P21.41 The maximum power that can safely be delivered to any one resistor is 25.0 W. (a) What is the maximum potential difference that can be applied to the terminals a and b? (b) For the voltage determined in part (a), what is the power delivered to each resistor? (c) What is the total power delivered to the combination of resistors?
(a) A defibrillator sends a 6.00-A current through the chest of a patient by applying a 10,000-V potential as in the figure below. What is the resistance of the path? (b) The defibrillator paddles make contact with the patient through a conducting gel that greatly reduces the path resistance. Discuss the difficulties that would ensue if a larger voltage were used to produce the same current through the patient, but with the path having perhaps 50 times the resistance. (Hint: The current must be about the same, so a higher voltage would imply greater power. Use this equation for power: P=I2 RP = .)
A circuit contains a D-cell battery, a switch, a 20- resistor, and three 20-mF capacitors. The capacitors are connected in parallel, and the parallel connection of capacitors are connected in series with the switch, the resistor and the battery, (a) What is die equivalent capacitance of the circuit? (b) What is the KC time constant? (c) How long before the current decreases to 50% of the initial value once the switch is closed?
An uncharged series RC circuit is to be connected across a battery. For each of the following changes, determine whether the time for the capacitor to reach 90% of its final charge would increase, decrease, or remain unchanged. Indicate your answers with I, D, or U, respectively. (a) The RC time constant is doubled. (b) The battery voltage is doubled. (c) A second resistor is added in series with the original resistor.
A resistor of an unknown resistance is placed in an insulated container filled with 0.75 kg of water. A voltage source is connected in series with the resistor and a current of 1.2 amps flows through the resistor for 10 minutes. During this time, the temperature of the water is measured and the temperature change during this time is T10.00C . (a) What is the resistance of the resistor? (b) What is the voltage supplied by the power supply?
Figure P18.26 shows a voltage divider, a circuit used to obtain a desired voltage Vout from a source voltage . Determine the required value of R2 if = 5.00 V, Vout = 1.50 V and R1 = 1.00 103 (Hint: Use Kirchhoff's loop rule, substituting Vout = IR2, to find the current. Then solve Ohms law for R2. Figure P18.26
Four resistors are connected to a battery as shown in Figure P27.15. (a) Determine the potential difference across each resistor in terms of . (b) Determine the current in each resistor in terms of I. (c) What If? If R3 is increased, explain what happens to the current in each of the resistors. (d) In the limit that R3 , what are the new values of the current in each resistor in terms of I, the original current in the battery? Figure P27.15
(a) What is the internal resistance of a voltage source if its terminal voltage drops by 2.00 V when the current supplied increases by 5.00 A? (b) Can the emf of the voltage source be found with the information supplied?