A circular shaft is subjected to combined loads of bending M and torque T. With the help of Mohr's circle diagram, represent the stresses on an element of the shaft surface. From this diagram or by calculation, find the maximum shear stress due to the combined effect of these gradually applied loads of M and T.

A circular shaft is subjected to combined loads of bending M and torque T. With the help of Mohr's circle diagram, represent the stresses on an element of the shaft surface. From this diagram or by calculation, find the maximum shear stress due to the combined effect of these gradually applied loads of M and T.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.11P: ‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses...

See similar textbooks

Similar questions

A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A 6-inch diameter pulley mounted on a 2-inch shaft as shown transmits 9 kW at 1000 rpm. What is the combined stress acting on the shaft?
A 180 mm diameter ship’s shaft rotates as 450 rpm and transmits 5 MW of power. The propeller causes an axial compression in the shaft of 1750 kN. Sketch the stress element on the shaft showing the three possible stress states. Hence, calculate for the position of maximum stress: 4.1 Principal stress on the shaft. 4.2 Maximum shear stress on the shaft. 4.3 The angle of maximum shear stress relative to the XY plane.
2. A hollow generator shaft of 180-mm outer diameter and 120-mm inner diameter carries a torque T= 40 kNm. Find the maximum tensile and compressive stresses in the shaft 12
When a steel rod below is subjected to torque (T = 1 kN · m) and bending moment (M = 4 kN · m) simultaneously, calculate equivalent stresses using Tresca's theory and Von-Mises' theory 2. M M 50mm
A 150 mm x a mm x 20 mm steel plate is subjected a pull of 150 kN along its central axis as show in figure. A hole of 40 mm diameter is drilled in the plate whose center is 50 mm alway from central longitudinal axis. Calculate the max stress in the plate. 20 min 40 min 40 nun 75 mm 50 mm 150 kN I50 km 75 mm
When a steel rod below is subjected to torque (T = 3 kN m) and bending moment (M = 2 kN m) simultaneously, calculate equivalent stresses using Tresca's theory and Von-Mises' theory 2. м M 50mm
Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm x 55 mm x 40 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 14 kN (tensile), 20 kN (compressive), 10 kN (compressive) respectively. Take E as 160 GPa, Poisson's ratio as 0.3 (ENTER ONLY THE VALUES IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKET & UPLOAD YOUR HAND WRITTEN ANSWERS IN THE LINK PROVIDED) The stress along length direction (Unit in MN/m?)=. The compressive stress along width direction (Unit in MN/m2)=. The compressive stress along depth direction (Unit in MN/m2)=. The change in volume of the block is (unit in mm3) =.
The torque shown in the figure is exerted on pulleys A, B and C. If it is known that the AB axis is solid and the BC axis is a tube with an outer diameter of 40 mm and an inner diameter of 20 mm, determine the maximum shear stress on the AB axis and on the BC axis.
1. Find the flexural stress at point A 2.5 kN/m 2.25 m 3.5 m
The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of 260 mm. Find the maximum shear stress in the cylinder for an internal pressure of 280 MPa.
The shaft, is driven by pulley B from an electric motor. Another belt drivefrom pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratioof belt tensions for pulley B is 3.5. The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable tensilestress for the shaft material is 170 MPa and the allowable shear stress is 85 MPa. Taking torsion andbending factors as 1.25 and 1.75 respectively, find the shaft diameter.Also find out the dimensions for a hollow shaft with outside diameter limited to 30 mm. Compare theweights of the two shafts. [Ans. 30 mm ; 24 mm ; 1.82 Given Length CD=350mm Length AB=150mm Length BD=100mm The total length is CD =350