A circular ring (radius = 5.0 cm) is used to determine the surface tension of a liquid. e plane of the ring is positioned so that it is parallel to the surface of the liquid. The g is immersed in the liquid and then pulled upward, so a film is formed between the g and the liquid. In addition to the ring's weight, an upward force of 3.6 x 10 N is quired to lift the ring to the point where it just breaks free of the surface. What is the face tension of the liquid?

A circular ring (radius = 5.0 cm) is used to determine the surface tension of a liquid. e plane of the ring is positioned so that it is parallel to the surface of the liquid. The g is immersed in the liquid and then pulled upward, so a film is formed between the g and the liquid. In addition to the ring's weight, an upward force of 3.6 x 10 N is quired to lift the ring to the point where it just breaks free of the surface. What is the face tension of the liquid?

Name: 2. A circular ring (radius = 5.0 cm) is used to determine the surface
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 2. A circular ring (radius = 5.0 cm) is used to determine the surface tension of a liquid.The plane of the ring is positioned so that it is parallel to the surface of the liquid. Thering is immersed in the liquid and then pulled upward, so a film is

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of the filled bowl. Approximate the bowl as a thin shell of radius R=6.15in. Use 1=162lb/ft3 for glass and 2=62.4lb/ft3 for water.
3. Consider a 0.15 mm diameter air bubble in a liquid. Determine the pressure difference between the inside and outside of the air bubble if the surface tension at the air-liquid interface is a.0.08 N/m b.0.12 N/m
1. A vertical semi-circular area of radius r is submerged in a liquid with its diameter in the liquid surface. How far is the center of pressure from the liquid surface? 2. An open vat holding oil (s=0.80) is 8 m long and 4 m deep and has a trapezoidal cross-section 3 m wide at the bottom and 5 m wide at the top. Determine the following: (a) the weight of oil, (b) the force on the bottom of the vat, and (c) the force on the trapezoidal end panel.
A Vertical circular gate or radius “r” is submerged in a liquid with its top edged flushed on the liquid surface. Determine the location of the total force acting on one side of the gate and its magnitude
A fluid filled container is shown below. Oil fills the left side of the “U” to a depth of 33.0 cm while water fills the rest. The oil has a density of 753 kg/m3. The radius of the tube on the left side is 27.0 cm and the radius of the tube on the right side is 38.0 cm. a. If the height of the fluid in the two cylinders is exactly the same, what mass should be placed on the left cylinder to balance the system. b. What is the pressure at the bottom of the oil when the system is balanced? c. If the mass on the left is removed, what is the difference in heights between the two sides?
A closed tank whose bottom is 18 inches in diameter is filled with three liquids: 4 inches of carbon tetrachloride (SG=1.59), 2 inches of water and 12 inches of syrup (SG=1.31). The air chamber in the tank is pressurized at 1296 psf. d. Apply the PANEL EQUATIONS to determine the magnitude, direction and location of the total hydrostatic force acting at the bottom of the tank.
A 98.43ft vertical column of fluid (density is 1878 kg/m3) is located where is 31.66ft/sec2. determine the pressure at the base of the column in kPa.
The manometer pictured has been filled with 2 different fluids and is open to the atmosphere on both sides. If fluid 1 has a density of 1g/cm3, the approximate density of fluid 2 is: Fluid 1 Fluid 2
A factory's pressure tank rests on the upper base of a vertical pipe whose inside diameter is 1 ft. and whose length is 40 ft. The tank is a vertical cylinder surmounted by a cone, and it has a hemispherical base. If the alti-tudes of the cylinder and the cone are respectively 6 ft. and 3 ft. and if all three parts of the tank have an inside diameter of 6 ft., find the volume of water in the tank and pipe when full.
A closed cylindrical tank 2m in diameter and 8m deep with axis vertical contains 6m deep of oil (SG =0.8). The air above the liquid surface has a pressure of 0.8 kg/cm2. Determine the total force and location of it from the bottom of the tank?
A circular plate 3.0 m diameter is immersed in water in such a way that the plane of the plate makes an angle of 60 degrees with the free surface of water. Determine the position of the center of pressure from the free surface when the upper edge of the plate is 2 m below the free water surface.