A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 245 mm, a wall thickness of 15 mm, and a length of 4.5 m. The pipe supports a compressive load of 610 kN. After the temperature of the pipe drops 49°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD= mm mm

A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 245 mm, a wall thickness of 15 mm, and a length of 4.5 m. The pipe supports a compressive load of 610 kN. After the temperature of the pipe drops 49°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD= mm mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.6.13P: A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean...

See similar textbooks

Similar questions

A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the figure. The width of the plate is h = 12.0 in. Measurements show that the normal strains in the x and v directions are s = 427 × 10-6 and s = 113 × l0-6, respectively. With reference to part b of the figure. which shows a Iwo-dimensional view of the plate. determine the following quantities. (a) The increase .d in the length of diagonal Oil. (b) The change . in the angle between diagonal Oti and the x axis, (c) The shear strain y associated with diagonals Oil and cf(that is. find the decrease in angle ced).
PROBLEM NO. 4 In Fig. 4, determine the normal stress and change in length of the aluminum rod if the temperature was raised by 129 C. The 0.5-mm gap exists at 28 C (0.59 mm 399 mm A Aluminum A = 2888 mm² E = 75 GPa α = 23 x 10°/°C 258 mm B Stainless Steel A = 899 mm² E = 190 GPa α = 17.3 x 10/°C
An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0x10-6/°C] pipe is subjected to a tensile load P. The pipe has an outside diameter of D = 280 mm, a cross-sectional area of A = 7550 mm², and a length of L = 9.5 m. The initial longitudinal normal strain in the pipe is zero. After load P is applied and the temperature of the pipe has been increased by AT = 40°C, the longitudinal normal strain in the pipe is found to be 2260 με. Calculate the magnitude of load P. Answer: P = M. L kN D P
A strain gage is mounted to the outer surface of a thin-walled boiler. The boiler has an inside diameter of 1820_mm and a wall thickness of 18 mm, and it is made of stainless steel [E = 179 GPa; v = 0.3]. Determine: (a) the internal pressure in the boiler when the strain gage reads 210 µɛ. (b) the maximum shear strain in the plane of the boiler wall. (c) the absolute maximum shear strain on the outer surface of the boiler. Answers: (a) p = i MPа. (b) Ymax in-plane = i prad. (c) Yabs max i prad. =
A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of 205 mm, a wall thickness of 11 mm, and a length of 4.2 m. The pipe supports a compressive load of 615 kN. After the temperature of the pipe drops 48°C, determine:(a) the axial deformation of the pipe.(b) the change in diameter of the pipe.
View Policies Current Attempt in Progress A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 245 mm, a wall thickness of 6 mm, and a length of 5.3 m. The pipe supports a compressive load of 635 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i mm AD = i mm Save for Later Attempts: 0 of 1 used Submit Answer
When installed, bar AB had negligible axial stress. When the bar's temperature is 124°F the axial compressive stress is 14.4 ksi. The bar is made from a ductile metal which has the following properties: E=25x10° psi, a = 9.00x10 6 (h)/°F, and v = 0.29. Assume elastic behavior. ( in. in. В 50 in.- Determine: a. The thermal strain in the bar's axial (longitudinal) direction if it could expand freely: b. Temperature at which bar was installed: c. The total strain in the lateral direction:
A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of 200 mm, a wall thickness of 10 mm, and a length of 4.8 m. The pipe supports a compressive load of 605 kN. After the temperature of the pipe drops 37°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe.
Problem #1: The bar below is composed of three solids cylindrical pieces with the diameters shown. The bar initially has a temperature of 70° F, and is slowly heated to a final temperature of 116° F. If the bar initially has zero stress, find the axial stress in each section when the bar reaches its final temperature. Young's Modulus (ksi) Coeff. Thermal Exp. (/°F) | 12.9×10-6 A Aluminum Bronze 10,600 15,000 11.1×106 9.6×10-6 2014-T6 Aluminum 12 in. 4 ft Stainless Steel 28,000 B C 86100 Bronze 8 in. 6 ft 304 Stainless steel C 4 in. 3 ft D
A steel tube is restrained between two rigid walls 80 cm apart, At a temperature of 28 degree celsius, the steel tube is stress free. What will be the stress, in MPa, in the tube when the temperature is 35 degree celsius? The steel tube has an outside diameter of 25 mm and a thickness of 1.5mm. Use a = 11.7x10^-6m/m-degree celsius and E = 200 GPa.
A solid bar of length L = 4 m and diameter 200 mm is heated from 20 to 320 degrees celsius and restrained between two solid immovable walls. Young's modulus of the material is 90 GPa and the coefficient of thermal expansion is 22 x 10-6/°C. →Calculate the thermal strain, e, in micro-strain correct to two decimal places. micro-strain. Calculate the thermal stress, o, in megapascals (MPa) correct to two decimal places. E: σ: MPa. Hence calculate the force exerted by the bar in meganewtons (MN) correct to two decimal places: F MN. L
Compound axial member ABC has a uniform diameter of d=1.45 in. Segment (1) is an aluminum [E1=10,000 ksi] alloy rod with a length of L1=88 in. Segment (2) is a copper [E2=17,000 ksi] alloy rod with a length of L2=128 in. When axial force P is applied, a strain gage attached to copper segment (2) measures a normal strain of ε2=2200 μin./in. in the longitudinal direction. What is the total elongation of member ABC? answer is in inches