A circuit that controls a given digital system has three inputs: x1, x2 and x3. It has to recognize three different conditions: 1) Condition A is true if x3 is true and either xl is true or x2 is false 2) Condition B is true if x1 is true and either x2 or x3 is false 3) Condition C is true if x2 is true and either x1 is true or x3 is false. The control circuit must produce an output of 1 if at least two of the conditions A, B, and C are true. Design and then draw the schematics of the simplest circuit that can be used for this purpose.

A circuit that controls a given digital system has three inputs: x1, x2 and x3. It has to recognize three different conditions: 1) Condition A is true if x3 is true and either xl is true or x2 is false 2) Condition B is true if x1 is true and either x2 or x3 is false 3) Condition C is true if x2 is true and either x1 is true or x3 is false. The control circuit must produce an output of 1 if at least two of the conditions A, B, and C are true. Design and then draw the schematics of the simplest circuit that can be used for this purpose.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Solve all please Q1) Choose the correct answer: I. The circuits can be divided into two broad categories analog and digital are called: a- control circuits b- logic circuits c- electronic circuits d- design circuits II. Magnitude comparison is performed by a logic circuit called a: III. a- divider b- multiplexer c- decoder d- comparator The resolution of 5 bits ADC from analog signal (-4-4)V is: a-0.2 b-0.22 c- 0.24 d-0.25 IV. The full scale output from analog signal (-4-4)V by using 5 bits ADC is: a- 3.7 b- 3.75 c-3.85 d-4
Q. A straight binary sequence is applied to a 4-bit DAC, and the output in figure below is observed. What is the problem? Output 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0000 1000 0010 0011- 0100 0101- 0110 0111- 0001 1001- 0101 1011 0011 1101- 0111 1111 Binary input Electrical Engineering Department/ University of Basrah
Q. A straight binary sequence is applied to a 4-bit DAC, and the output in figure below is observed. What is the problem? Output 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0000 1000 0010 0011 0010 -1010 0110 1110 0001 1001- -otor 1011 H0011 1101- 0111 1111 Binary input Electrical Engineering Department/ University of Baura
Transfer Instructions H.W2 Write the necessary instruction to change or swap 3 byte stored at DS:0A60 with DS:0A80 Solution:
Q3Using the partial fractivn methad find XcA fur Rop Roc %3D Q4 Find the output respunse if the freghency vespanse of the is He@s system. for the futtowina 2+jw input XH uct)
In the following circuit, X and Y values are connected to the Multiplexer inputs. Decimal values of X and Y are given as follows: X= - 2 Y= - 12 Note that both X and Y have negative values and they are represented in TYPE 2 representation, where Type 1:One's complement Type 2: Two's complement Type 3: Signed Magnitude a) Find 4-bit input values X3 X2 X1 X0 and Y3 Y2 Y1 Y0. b) Find the boolean expression for the function F2 in terms of variables A, B, C, D. c) Simplify the function you found in part b) using the karnaugh map method. Do not forget to write down the decimal value of X, Y and the representation type in your solution. |Cin хо 10 YO 10 A S F1 11 4:1 11 4:1 X1 Y1 X2 12 Mих Y 12 Mux Cout F2 Y2 • B X3 13 Y3 13 FULL si so si so ADDER А В C D
The logic function implemented by the multiplexer circuit is (ground implies a logic "0") 4x1 MUX 1。 1₁ 1₂ 13 S₁ S₂ P Q Y -F
Design a combinational circuit with three inputs and one output. a. The output is 1 when the binary value of the inputs is less than 3. Theoutput is 0 otherwise.b. The output is 1 when the binary value of the inputs is an even number.
Q44) In the STM diagram fragment below, we see five transitions marked with italic letters. Which option cannot have a guard condition added? dev2/x=x+1 A. a B. b C. c D. d E. e b a/beh Ev1/beh с e
Q1) Choose the correct answer: Solve all please I. The circuits can be divided into two broad categories analog and digital are called: a-control circuits b- logic circuits c- electronic circuits d- design circuits II. Magnitude comparison is performed by a logic circuit called a: a- divider b- multiplexer c- decoder d- comparator The resolution of 5 bits ADC from analog signal (-4-4)V is: a- 0.2 b-0.22 c- 0.24 III. IV. V. d- 0.25 The full scale output from analog signal (-4-4)V by using 5 bits ADC is: a- 3.7 b-3.75 c-3.85 d-4 The number of quantization level of 10 bit ADC from analog signal (-5~5)V is: a- 128 b- 256 c- 32 d-1024
Q11/Chose the correct answer for the output Q3 of the following circuit (Assume that A= 1010101010, and B =1110111011 and the first bit out from the circuit is bit 0) * T. Q1 Q3 CLK CLK QI' Q3' K B Q2 CLK Q2' CLK CLK Q3=1000100010 Q3=1001100110 Q3=0010110011 Q3=1001000100 None of them
a) Fill in the table below for 4-bit A/D converter if Va = 13V with a reference voltage of 15V. Show your work. Analog " Table - Successive approximation process for Va = 13V Vb B3 B₁ Step 1 B₂ 0 8V 1 0 Bo 0 Clock Comparisons Is Va ≥ 8V F Sample-and-hold 4- SAR 4- DAC 4-bit register Logic control Ring counter Answer Yes gffffe MSB LSB Output