A certain half-reaction has a standard reduction potential E=-0.23 V. An engineer proposes using this half-reaction at the cathode of a galvanic cell that red must provide at least 1.30 V of electrical power. The cell will operate under standard conditions. Note for advanced students: assume the engineer requires this half-reaction to happen at the cathode of the cell. dlo Is there a minimum standard reduction potential that the half-reaction used at the anode of this cell can have? O yes, there is a minimum. = Ov If so, check the "yes" box and calculate the minimum. Round your answer to 2 decimal places. If there is no lower limit, check the "no" box. O no minimum Is there a maximum standard reduction potential that the half-reaction used at the anode of this cell can have? Ered = Ov yes, there is a maximum. If so, check the "yes" box and calculate the maximum. Round your answer to 2 decimal places. If there is no upper limit, check the "no" box. O no maximum By using the information in the ALEKS Oata tak uite a halas BRuntien

A certain half-reaction has a standard reduction potential E=-0.23 V. An engineer proposes using this half-reaction at the cathode of a galvanic cell that red must provide at least 1.30 V of electrical power. The cell will operate under standard conditions. Note for advanced students: assume the engineer requires this half-reaction to happen at the cathode of the cell. dlo Is there a minimum standard reduction potential that the half-reaction used at the anode of this cell can have? O yes, there is a minimum. = Ov If so, check the "yes" box and calculate the minimum. Round your answer to 2 decimal places. If there is no lower limit, check the "no" box. O no minimum Is there a maximum standard reduction potential that the half-reaction used at the anode of this cell can have? Ered = Ov yes, there is a maximum. If so, check the "yes" box and calculate the maximum. Round your answer to 2 decimal places. If there is no upper limit, check the "no" box. O no maximum By using the information in the ALEKS Oata tak uite a halas BRuntien

Chemistry

9th Edition

ISBN:9781133611097

Author:Steven S. Zumdahl

Publisher:Steven S. Zumdahl

Chapter18: Electrochemistry

Section: Chapter Questions

Problem 160MP: The table below lists the cell potentials for the 10 possible galvanic cells assembled from the...

See similar textbooks

Similar questions

A standard galvanic cell is constructed so that the overall cell reaction is 2A13++(aq)+3M(s)3M2+(aq)+2A1(s) Where M is an unknown metal. If G = 411 kJ for the overall cell reaction, identify the metal used to construct the standard cell.
A galvanic cell is constructed in which the overall reactionis Cr2O72(aq)+14H2O+(aq)+6I(aq)2Cr3+(aq)+3I2(s)+21H2O(l) Calculate E for this cell. At pH 0, with [Cr2O72]=1.5M and [I]=0.40M, the cell potential is found to equal 0.87 V. Calculatethe concentration of Cr3+(aq) in the cell.
Consider a galvanic cell for which the anode reaction is 3 Pb(s)Pb2+(1.0102M)+2e and the cathode reaction is VO2+(0.10M)+2H3O+(0.10M)+eV3+(1.0105M)+3H2O(l) The measured cell potential is 0.640 V. Calculate E for the VO2+V3+ half-reaction, usingE(Pb2+Pb) from Appendix E. Calculate the equilibrium constant (K) at 25°C for thereaction Pb(s)+2VO2+(aq)+4H3O+(aq)Pb2+(aq)+2V3+(aq)+6H2O(l)
Determine the overall reaction and its standard cell potential at 25 C for this reaction. Is the reaction spontaneous at standard conditions? Cu(s)|Cu2+(aq)Au3+(aq)|Au(s)
a Calculate G for the following cell reaction: Tl(s)Tl+(aq)Pb2+(aq)Pb(s) The Gf for Tl+(aq) is 32.4 kJ/mol. b From G, calculate the standard cell potential for the cell reaction and from this, determine the standard potential for Tl2+(aq)+eTl(s).
Is it reasonable to conclude that a potential could be assigned to each half-cell in a voltaic cell, based on these data for three voltaic cells? Explain. Zn(s)|Zn2+(aq)||Cu2+(aq)|Cu(s) cell potential=1.10 V Zn(s)|Zn2+(aq)||Ag+(aq)|Ag(s) cell potential=1.56 V Cu(s)|Cu2+(aq)||Ag+(aq)|Ag(s) cell potential=0.46 V
The table below lists the cell potentials for the 10 possible galvanic cells assembled from the metals A. B. C. D. and E. and their respective 1.00 M 2+ ions in solution. Using the data in the table, establish a standard reduction potential table similar to Table 17-1 in the text. Assign a reduction potential of 0.00 V to the half-reaction that falls in the middle of the series. You should get two different tables. Explain why, and discuss what you could do to determine which table is correct. A(s)in A2+(aq) B(s)in B2+(aq) C(s)in V2+(aq) D(s)in D2+(aq) E(s)in E2+(aq) 0.28V 0.81V 0.13V 1.00V D(s)in D2+(aq) 0.72V 0.19V 1.13V C(s)in V2+(aq) 0.41V 0.94V B(s)in B2+(aq) 0.53V
The mass of three different metal electrodes, each from a different galvanic cell, were determined before and after the current generated by the oxidation-reduction reaction in each cell was allowed to flow for a few minutes. The first metal electrode, given the label A, was found to have increased in mass; the second metal electrode, given the label B, did not change in mass; and the third metal electrode, given the label C, was found to have lost mass. Make an educated guess as to which electrodes were active and which were inert electrodes, and which were anode(s) and which were the cathode(s).
Halide ions can he deposited at a silver anode, the reaction being Ag(s) + X- AgX(s) +e- Suppose that a cell was formed by immersing a silver anode in an analyte solution that was 0.0250 M Cl-,Br-, and I -ions and connecting the half-cell to a saturated calomel cathode via a salt bridge. (a) Which halide would form first and at what potential? Is the cell galvanic or electrolytic? (b) Could I- and Br- be separated quantitatively? (Take 1.00 l0-5 M as the criterion for quantitative removal of an ion.) If a separation is feasible, what range of cell potential could he used? (c) Repeat part (b) for I- and Cl-. (d) Repeat part (b) for Br- and Cl-.