A carbon steel shaft AB is fixed with two gears and is applied with 4 torque as shown in Figure 1. The G value of carbon steel is 80 GPa. The outer diameter of the shaft is 40 mm. Shaft AC and shaft DB are hollow with inner diameter of 20 mm, while shaft CD is solid. 300 Nm so0 N 200 Nm 400 Nm 300 mm 400 mm 500 mm Figure 1. a) For each section of the shafts, determine the maximum shearing stress. b) For each gear, determine its angle of twist. c) Determine the angle of twist of end B with respect to A

A carbon steel shaft AB is fixed with two gears and is applied with 4 torque as shown in Figure 1. The G value of carbon steel is 80 GPa. The outer diameter of the shaft is 40 mm. Shaft AC and shaft DB are hollow with inner diameter of 20 mm, while shaft CD is solid. 300 Nm so0 N 200 Nm 400 Nm 300 mm 400 mm 500 mm Figure 1. a) For each section of the shafts, determine the maximum shearing stress. b) For each gear, determine its angle of twist. c) Determine the angle of twist of end B with respect to A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two solid circular shafts are connected by two rigid gears. Note shaft ab is a composite shaft. Determine the angle of twist at point 'a' in degrees to two decimal places. solid shaft 60 in $= 11/1535 TL GJ J=TY/2r4 b composite shaft C 35 in bearing Notes:- gear b radius = 6.0 in - gear c radius = 4.0 in - shaft ab outer radius= 1.5 in - shaft ab inner radius= 1.1 in - shaft cd radius= 1.0 in - shaft ab inner shear modulus = 12000 ki - shaft ab outer shear modulus = 3000 ksi - shaft cd shear modulus = 12000 ksi outer portion inner portion shaft ab cross-section 2.86 in-kip
(3) A mechanism consists of two flexible shafts: shaft1 and shaft 2 which are connected by gear I and gear 2. Each shaft is fixed on one end at a fixed support. Gear 1 J.N Fored Support Shaft 1 Fied Support Shaft 2 Gear 2 length of shaft 1: 1 = 0.3 m; length of shaft 2: 1= 0.2 m; diameter of shaft 1 and shaft 2: d=0.01m; gear number N-48; gear number Ny= 24; density of shaft I and shaft 2 material p = 6000 kg/m³. the two gears have moment of inertia J 4 10 kg m², and J;= 1-10* kg m² Determine the equivalent moment of inertia, Jeg, of the system at the coordinate Oj shown in the figure.
1) A pair of cast iron bevel gears connect two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm respectively. The tooth profiles of the gears are of 14 1/2° composite form. The allowable static stress for both the gears is 55 MPa. If the pinion transmits 2.75 kW at 1100 r.p.m., find the module and number of teeth on each gear from the standpoint of strength and check the design from the standpoint of wear. Take surface endurance limit as 630 MPa and modulus of elasticity for cast iron as 84 kN/mm2.
1) A pair of cast iron bevel gears connect two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm respectively. The tooth profiles of the gears are of 14 1/2° composite form. The allowable static stress for both the gears is 55 MPa. If the pinion transmits 2.75 kW at 1100 r.p.m., find the module and number of teeth on each gear from the standpoint of strength and check the design from the standpoint of wear. Take surface endurance limit as 630 MPa and modulus of elasticity for cast iron as 84 kN/mm². A0a& ENG 1222/20 nere to search
2- The four gears shown in the below Fig. are attached to a 50- mm diameter steel shaft. Compute the angle of twist of gear A relative to the gear D. Take G= 83 GPa. 800 N.m 1400 N.m 1200 N.m D 600 N.m 1.5 m В 1.2 m 2.0 m A
The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
A train of spur gears is shown in the 2 points Figure below. Gear 1 is the driving gear. The pitch circular diameters of gears 1, 2, 3 and 4 are 100, 400, 100 and 400 respectively. The module for all gears is 4 mm. The gears have a 20° full-depth involute profile. The ratio factor Q for these gears is. Output shaft 3 Input shaft 1.341 1.6 1.5 1.42 2.
In the figure below the gears are 20º full depth of AGMA Quality No 8. a) Find the horsepower transmitted by the 1-2 mesh b) Find the required width b for the 3-4 mesh if they are carrying the same horsepower as the 1-2 mesh. No.2, C.I. BHN=220 P=4, N₂=72,b=2" No 1, Steel, P=4, N₁=24,b=2" n₁ = 570 rpm /No.4.CI. BHN=220 P=3, N₂=72 No.3, Steel, P=3, N₁=24
You have been asked by your engineering company to design a complete gear and shaft system shaft that is made of steel. The solid shaft is linked with gear A, B. C and D with gear A., B and C produces torque of 15 kNm (clockwise), 30 kNm (clockwise) and 75kNm (anticlockwise). respectively each. If AB = 0.70m, BC= 0.80 m and CD=0.90 m with the shafts consist of solid circular shafts with a diameter of 150 mm having the shear modulus of G = 80 GPa, b) The shafts are now to be redesigned by drilling only through shaft BC with a diameter hole, cz to produce a hollow shaft BC. It is also known that the allowable shear stress, Tall in the shaft must not exceed 85 MPa. i) Determine the minimum wall thickness of the shaft BC, tBc
NEED DETAILED ANSWER ASAP, THANK YOU The four rigid gears, loaded as shown in the figure, are attached to a 2.89-in.-diameter steel shaft. Compute the angle of rotation of gear A relative to gear D if TA = 414 lbft, TB = 911 lbft, and TC = 1156 lbft. Use G = 12041783 psi for the shaft. Round off the final answer to four decimal places.
You have been asked by your engineering company to design a complete gear and shaft system shaft that is made of steel. The solid shaft is linked with gear A, B, C and D with gear A, B and C produces torque of 15 kNm (clockwise), 30 kNm (clockwise) and 75kNm (anticlockwise). respectively each. If AB = 0.70m, BC=0.80 m and CD=0.90 m with the shafts consist of solid circular shafts with a diameter of 150 mm having the shear modulus of G= 80 GPa. a) Design and detemine the portion of the shaft which has the largest magnitude of shear stress, (7)max. Include free body diagram (FBD) in your analysis.
A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 400 The shaft is mounted on two 400 400 270 250 ]640 210 640 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 100