A cantilever beam is subjected to a point load and a moment as shown in Figure Q1. Use Area Moment Method and draw the elastic curve to a. To determine the possible positions (x's) of the greatest deflection wrt section/point A. b. To determine the deflection at B (where P is applied) c. To determine the magnitude and direction of the greatest deflection but in terms of P, L, E and I.

A cantilever beam is subjected to a point load and a moment as shown in Figure Q1. Use Area Moment Method and draw the elastic curve to a. To determine the possible positions (x's) of the greatest deflection wrt section/point A. b. To determine the deflection at B (where P is applied) c. To determine the magnitude and direction of the greatest deflection but in terms of P, L, E and I.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 512 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 643 mm2. For the 32 kN force shown, determine the deflection of D (mm) *Note: Negative if compression and positive if tension. Also, the final answer should have two decimal places.
As shown in the figure, aluminum, E= 70GPa links (1) and (2) support rigid beam ABC. Link (1) has a cross-sectional area of 320mm² and link (2) has a cross-sectional area of 480mm². For an applied load of P= 58kN, determine the rigid beam deflection at point B. (2) 4,000 mm (1) 2,500 mm B 1,400 mm 800 mm
Use CONJUGATE BEAM METHOD to Determine the following: A central beam BD is joined at hinges to two cantilever beams AB and DE. All beams have the cross-section shown. For the loading shown, determine the largest w so that the deflection at C does not exceed 3mm. Use E=200 GPa. w 12 mm |A C D E Hinge `Hinge 24 mm 0.4 m 0.4 m 0.4 m 0.4 m
The beam system shown below has a fixed support at A, roller support at C, internal hinge at B. Find the deformations at B and the maximum deflection within the span BC. Use Moment Area Theorems to find deformations
Solve for: a. value of maximum deflection b. moment of inertia [Ix, ly, centroids (xbar & ybar)] c. maximum shear stress d. maximum bending stress e. maximum tensile f. maximum compressive
Question 1: Analyze and determine the deflection at the end B of the clamped A-36 steel strip. The spring has a stiffness of k = 2 N/mm. The strip is 5 mm wide and 10 mm high. Also, draw the shear and moment diagrams for the strip. Use the method of consistent deformation in your calculations. 50 N -200 mm B A k = 2 N/mm 10 mm
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; /= 1780 in.4]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 170 kip-ft, P = 29 kips, LAB = 5.7 ft, LBC = 8.6 ft. MA LAB P B LBC
Compute the deformation of the beam using conjugate method E= 200 GPa I= 1000 x 106 mm4
A loaded beam is shown in figure. EI B Rigid L 2 M M AB is flexible and 'BC' is rigid. Maximum deflection is
The beam has a rectangular cross section and is subjected to the loading shown. Determine the components of stress ox, oy, and Txy at point B. 800 N B 1000 N 15 mm 20 mm 20 mm 15 mm 100 mm 10 mm
A truss is subjected to loads as shown. Assume AE is constant and use virtual work method for deflection of truss. 4m 120 KN B A TINT 3m EA = constant E = 200 G Pa 2 A = 1,500 mm Find the vertical deflection at B in mm
For the beam and loading shown determine (a) the equation of the elastic curve, (b) the deflection at the left end of the beam. Assume that EI is constant for the beam. w(x)=w₁ x ³/L³ Wo T L B