A Boolean function F(A,B,C) = A.B+B.C.1.Implement the function using(a)8-to-1 multiplexer.A B cF0 0I,I211F111Is1Sz S, So111A B C(b)4-to-1 multiplexer.A B FF11S, SoA B2.Implement the function using 4-to-1 multiplexer with B and C connected to theselect bits Si and So respectively.в сF0 0I,FS, So1в с

MULTIPLEXER: The multiplexer is a combinational circuit that is used to connect multiple input…

A Boolean function F(A,B,C) = Ā.B+B.C. 1. Implement the function using 8-to-1 multiplexer. (a) AB c F 0 0 0 Is 1 Sz S, So AB C (b) 4-to-1 multiplexer. A BF 0 0 S, So A B 2. Implement the function using 4-to-1 multiplexer with B and C connected to the select bits Sı and So respectively. C F F S, So в с

A Boolean function F(A,B,C) = Ā.B+B.C. 1. Implement the function using 8-to-1 multiplexer. (a) AB c F 0 0 0 Is 1 Sz S, So AB C (b) 4-to-1 multiplexer. A BF 0 0 S, So A B 2. Implement the function using 4-to-1 multiplexer with B and C connected to the select bits Sı and So respectively. C F F S, So в с

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Design a combinational circuit with the four inputs A,B.C, and D, and three outputs X, Y, and Z. When the binary input is odd number, the binary output is one lesser than the input. When the binary input is even number the binary output is one greate than the input. Implement the function using multiplexers with minimal input and select line.
H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.
Which function performs the following operation? Give the assembly instruction and show your work.  Before A= 11011011, CF=1 After A= 10111101, CF=1
USE DIGITAL LOGIC AND DESIGN Part 1: In Figure_4; we have 4-bit Comparator using 2-bit Comparators block. You have to satisfy given condition by applying all data on figure 4. At the end, given condition should produce HIGH output and other two should be LOW. A3 A2 A1 A0 = 1101 and B3 B2 B1 B0 = 1110 Figure_4 Part 2: The serial data-input waveform (Data in) and data-select inputs (S0 and S1) are shown in Figure_5. Determine the data-output waveforms from D0 through D3. Figure_5 Part 3: Decoder can be useful when we have to decode some specific numbers from their equivalent code. Figure 6 has a concept of 3 to 8 line decoder from which you have to generate output waveform from D0 to D7 with proper relationship to input. Figure_6 Part 4: The data-input and…
Design a code converter that converts a decimal digit from BCD to excess-3 code, the input variables are organized as (A BC D) respectively with A is the MSB, the output variables are organized as (W XY Z) respectively with W is the MSB, put the invalid decimal numbers as don't care. X= BCD'+B'D+B'C X= BC'D'+B'D+BC X= BC'D'+B'D+B'C X= BC'D'+BD+B'C
Design a code converter that converts a decimal digit from BCD to excess-3 code, the input variables are organized as (A BC D) respectively with A is the MSB, the output variables are organized as (W X Y Z) respectively with W is the MSB, put the invalid decimal numbers as don't care. X= BCD'+B'D+B'C X= BC'D'+B'D+BC X= BC'D'+B'D+B'C X= BC'D'+BD+B'C
5. Assume d3d₂d₁do is a BCD number and derive Boolean expression for segments b,c,e,f,g in a seven segment display in terms of d3d₂d₁do g 4 d Based on your boolean expressions derive the values of b,c,e,f,g segments when i. d3d₂d₁do= (0100) 2 ii. d3d₂d₁do = (0111)₂ iii. d3d2d₁do (1000)2
ii) For the circuit shown in Figure B9, a. Find logic functions for Y and Z. b. Simplify function Z using Boolean algebra. Y Figure B9 AB
parity generator design, construct and test a circuit that generates an even parity bit ffrom four messages bits . use XOR gates. adding one more XOR gate, expand the circuit so that it generates an odd parity bit also.
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False