A block weighing 200 N is just moved on a rough horizontal plane by a pull of 90 Newton acting at an angle of 30 degree with the horizontal. Determine: (i) the coefficient of friction . (ii) Push that should be applied to the block at the same angle to attain the condition of limiting equilibrium

A block weighing 200 N is just moved on a rough horizontal plane by a pull of 90 Newton acting at an angle of 30 degree with the horizontal. Determine: (i) the coefficient of friction . (ii) Push that should be applied to the block at the same angle to attain the condition of limiting equilibrium

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.66P: The blocks A and B of weights WA and WB are joined by a rope that passes over the fixed peg C. The...

See similar textbooks

Related questions

Q: Two blocks of weights W1 = W2 = 5 kN rest on a rough plane and are connected by a short piece of…

Q: A small 200-g collar C can slide on a semicircular rod that is made to rotate about the vertical AB…

A: Write the expression of the velocity of the mass.

Q: Knowing that the coefficient of static friction is 0.30 between the rope and the horizontal pipe and…

A: (a) Free-body diagram of rope for horizontal and vertical pipes, The contact angle for the…

Q: Determine the maximum and minimum values of weight "W" that the block on the left can have without…

A: Given: The load on an inclined plane, w = 100 N The coefficient of friction between the block and…

Q: A lever AB of negligible weight is loosely fitted onto a 2.5-in.-diameter fixed shaft. Knowing that…

A: Free-body diagram shaft-lever arrangement is given as, The friction-gap is written as,

Q: A lever AB of negligible weight is loosely fitted onto a 2.5-in.-diameter fixed shaft. Knowing that…

A: The radius of shaft r = 2.5/2 inch = 1.25 in. The coefficient of static friction is μs = 0.15 N The…

Q: *Show clearly all pertinent solutions and state the assumptions made, if any. The 25kg block shown…

Q: A homogeneous block of weight W rests upon the incline shown in the figure. If the coefficient of…

A: Given data as per question coefficient of friction = 0.30 considering…

Q: A block with weight W is pulled up a plane forming an angle a with the horizontal by a force P…

Q: The arms of a Porter governor are 375 mm long. The upper arms are pivoted on the axis of rotation.…

Q: If the breaking strength of the cable is 2000N, determine the maximum weight that can be supported.…

Q: Two blocks A and B, each having a mass of 7 kg , are connected by pins using the linkages shown. B А…

A: Given data and FBD

Q: HW5 The arms of a Porter governor are 300 mm long. The upper arms are pivoted on the axis of…

A: Introduction: When the load on the engine rises, the speed of the engine decreases at the time…

Q: 2.5 kg block is initially at rest on a horizontal surface. A horizontal force of magnitude 5.8 N…

Q: The friction tongs shown in Figure are used to lift a 350 kg casting. Knowing that h = 864 mm,…

A: Given Data:- M = 350 kg H = 864 mm Find:- Smallest allowable friction coefficient M = ?…

Q: npenc negligible except for the surface under B whose coefficient of friction is 0.20. (b) Determine…

Q: A 12 ft ladder weighing 40 lb is placed. When a 180 lb man reaches a point 8ft from the lower end,…

Q: The 10-kg block is attached to link AB and rests on a conveyor belt that is moving to the left.…

Q: Block A supports a pipe column and rests as shown on wedge B . Knowing that the coefficient of…

A: As per given Coefficients of friction =0.25 θ = 45° We have to determine the smallest force P

Q: Two blocks A and B weighing 3 kN and 15 kN, respectively, are held in position against an inclined…

A: In the given friction problem, free body diagrams will be drawn for block A and B and the problem…

Q: Question 2: 0.6 m- The uniform 60-kg crate C rests uniformly on a 10-kg dolly D. If the front…

A: The weight of the crate is Wc=mcg=60×9.81=588.6 N The weight of the dolly is WD=mDg=10×9.81=98.1 N…

Q: A 1.2-m plank with a mass of 3 kg rests on two joists. Knowing that the coefficient of static…

A: Given data: Mass of the plank, m = 3 kg Coefficient of friction, μ = 0.3 Let, g = acceleration due…

Q: A horizontal force of 200 lb is required to push an 800-lb piano across a level carpeted floor. The…

A: Given that, Horizontal Force, Fh=200 lbWeight of piano, Wp=800 lbDiamter of wheel, d=2 in The load…

Q: Determine the maximum allowable value of weight W at rest. Knowing that the coefficient of static…

Q: Blocks A and B have a mass of 100 kg and 150 kg, respectively. If the coefficient of static friction…

A: The Law of equilibrium states that when all the external forces are balanced then the body is in…

Q: Solve Prob. 8.13 assuming that package B is placed to the right of both packages A and C.(Reference…

A: Package B is placed at right side of A and C. Given, Weight of all three package = 4 kg Between…

Q: The coefficient of static frictions between the 96-lb body and the 18° wedge is 0.19. Determine the…

A: (a) To find: The magnitude and the direction of the force P. Given: The weight of the body is 96 lb.…

Q: The 150 Newton weight is attached to a rope that passes over two fixed Cylinders A & B. The…

Q: Two 10° wedges of negligible weight are used to move and position the 400-lb block. Knowing that the…

Q: A lever AB of negligible weight is loosely fitted onto a 2.5-in.-diameter fixed shaft. Knowing that…

A: Given: The diameter of the shaft, d = 2.5 in The coefficient of friction between shaft and lever, μ…

Q: 4. The position of the machine block B is adjusted by moving the wedge A. Knowing that the…

A: A) Raising the Machine: f1 = μN1 = 0.35N1 f2 = μN2 = 0.35N2 Applying the Equilibrium Equations…

Q: Blocks A and B are held in place in a plane inclined at an angle 8. Block B, located 1m from the…

Q: 1. Determine the maximum allowable value of weight W at rest. Knowing that the coefficient of static…

Q: Block A supports a pipe column and rests as shown on wedge B. Knowing that the coefficient of static…

A: Given data μ=0.25 θ=45ο

Q: A single-pneumatic cylinder has an internal diameter of 50mm and a piston which is required to exert…

A: Given data: internal diameter (d) = 50mm Force (F) = 1.5 kN Need to determine the gauge pressure is…

Q: If each box weighs 150 lb, determine the least horizontal force P that the man must exert on the top…

Q: A 60 kN load is placed on two tires of a locked-wheel trailer. At a speed of 48 km/h, a force of 30…

Q: Two 10-lb blacks A and B are connected by a slender rod of negligible weight at rest. the…

Q: Two blocks A and B, each having a mass of 7 kg , are connected by pins using the linkages shown. B…

A: Suppose T1 tension in linkage AC and T2 tension in linkage BC. Use Lami's theorem P/sin70 =…

Q: A 10° wedge is used to split a section of a log. The coefficient of static friction between the…

A: Given data as per the question The angle of wedge =100 coefficient of static friction between the…

Q: A 16-lb spool is at rest on an inclined surface. Around its center a cable is wound which travels…

Q: A rectangular plate with a weight of W is supported by collars A and B. Collar A slides on a smooth,…

Q: 0° В 0° A 0° Two blacks A and B, each having a weight of 9 lb., are connected by the linkage shown…

Q: A rope having a weight per unit length of 0.4 lb/ft is wound 2 1/2 Times around a horizontal rod.…

A: T1=0.4x T2=100+0.4(10)=104N

Q: 4 ft A 5 ft→ 7 ft→B At a forward speed of 30 ft/s, the truck brakes were applied, causing the wheels…

Q: B 2. A 2.4 m ladder rests on a vertical wall as shown in the figure. The ladder has seven rungs and…

Q: A flat belt connects pulley a, which drives a machine tool, to pulley b, which is attached to the…

Q: What weight W must be suspended through the fixed pulley shown to start motion to the left of the…

A: Given data The weight of the wedge A is WA=1500 N The weight of the wedge B is WB=3000 N The…

Q: The slender, uniform bar BC with a mass of 6 kg rests on the center of the 300x200 mm block of mass…

Q: A 12° wedge is used to spread a split ring. The coefficient of static friction between the wedge and…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The blocks A and B of weights WA and WB are joined by a rope that passes over the fixed peg C. The coefficients of static friction are =0.2 between block A and the inclined plane, and =0.25 between the rope and the peg. Determine the range of Wb/WA for which the system will be in equilibrium.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
A 1.1-kg disk A is placed on the inclined surface. The coefficient of static friction between the disk and the surface is 0.35. Is the disk in equilibrium if P=5.5N and =30?
Draw the FBD of the entire frame, assuming that friction and the weights of the members are negligible. How many unknowns appear on this FBD?
The cone clutch transmits the torque C through a conical friction surface with cone angle . The inner and outer radii of the friction surface are a and b, respectively. The left half of the clutch is keyed to the shaft, and the right half drives a machine (not shown) through a gear attached to its outer rim. Assuming uniform pressure on the friction surface, show that the maximum torque that can be transmitted by the clutch is
The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
As shown, a man is leaning against the side of a cabinet with an unusual design. The cabinet's main body weighs 25 kg, while the upper rectangular portion weighs 3 kg. Assume the coefficients of friction between the cabinet and the floor are μs = 0.33 and μk = 0.28. Knowing that the force P exerted by the man's shoulder on the horizontal cabinet: 2. Determine which of the following is the CORRECT equilibrium equation obtained from the system's force diagram. A. ΣF = 0: N - 245.25 = 0B. ΣF = 0: P - μ N = 0C. ΣM = 0: 245.25(0.55) + 29.43(0.2) - N(x) - P(1.5) = 0
Q4.) An 8-foot-long uniform slender rod is connected to a 20-lb. block by a cord and pulley system as shown where LAO = 6 ft. The coefficient of static friction between the block and the surface is 0.6. Determine the range of rod weights for which the system remains in equilibrium. Assume friction is negligible between the pulleys and the cord. Consider both slipping and tipping. 30° 30° 6 ft 2.5 ft/ B 2 ft 40⁰ 3.5 ft
A 60-kg cabinet is mounted on casters that can be locked to prevent their rotation. The coefficient of static friction between the floor and each caster is 0.35. 1. If h = 600 mm, determine the magnitude of the force P (in N) required to move the cabinet to theright, if all the casters are locked. (ANSWER: 206) 2. If h = 600 mm, determine the magnitude of the force P (in N) required to move the cabinet to the right if the casters at B are locked and the casters at A are free to rotate. (ANSWER: 178)
A clockwise couple M is applied to the circular cylinder as shown. Determine the value of M required to initiate motion for the conditions mg = 4.6 kg, mc - 4.7 kg, (s)B=0.46, (c=0.34, and r=0.21 m. Friction between the cylinder C and the block B is negligible. (s)c Answer: M = mc M mg (₂)B N.m
A 120-lb cabinet is mounted on casters that can be locked to prevent their rotation. The coefficient of static friction between the floor and each caster is 0.30. Assuming that the casters at both A and B are locked, determine (a) the force P required to move the cabinet to the right, (b) the largest allowable value of h if the cabinet is not to tip over.