A block of mass 2.40 kg is placed against a horizontal spring of constant k = 825 N/m and pushed so the spring compresses by 0.0750 m. HINT (a) What is the elastic potential energy of the block-spring system (in J)? (b) If the block is now released and the surface is frictionless, calculate the block's speed (in m/s) after leaving the spring. m/s

A block of mass 2.40 kg is placed against a horizontal spring of constant k = 825 N/m and pushed so the spring compresses by 0.0750 m. HINT (a) What is the elastic potential energy of the block-spring system (in J)? (b) If the block is now released and the surface is frictionless, calculate the block's speed (in m/s) after leaving the spring. m/s

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

m h A block of mass m sliding down an incline at constant speed is initially at a height above the ground, as shown in the figure. The coefficient of friction between the mass and the incline is k. If the mass continues to slide down the incline at a constant speed, how much energy is dissipated by the friction by the time the mass reached the bottom of the incline? mgh/k kmgh/cos(Theta) kmgh/sin(Theta) mgh
A 200-kg log is pulled up a ramp by means of a rope that is parallel to the surface of the ramp. The ramp is inclined at 34.5° with respect to the horizontal. The coefficient of kinetic friction between the log and the ramp is 0.870, and the log has an acceleration of 0.750 m/s2. Find the tension in the rope.
A wooden block(s) of mass M= 400 gram and m = 100 gram is the total mass just starts to move when the hanger mass 200 gram. The tension in the cord is: O a. 2N O b. 0.5N O C. SN O d. 0.2N 400g 100g motion surface with friction 1200g
1. It takes 20 seconds to lift a 1600-kg car and the underlying 300-kg platform of a hydraulic lift to a height of 2.8 m. What is the average power output of the hydraulic system, and the efficiency if the electrical power input to the pump is 3200 W?
Consider the following diagram. m1320 kg and m2= 10 kg. The system is being pulled by an applied force of 200 N, directed 50 above the horizontal. The coefficient of kinetic friction between the block and the surface is u=0.2. 500 20kg m, 10 kg Coeficent of friction 4= 0.2 30 7) Calculate the acceleration of the system. * Your answer 8) Calculate the magnitude of the Tension on the rope. Your answer
A block of mass 10 kg rests on a horizontal floor. The acceleration due to gravity is 9.81 m/s2. The coefficient of static friction between the floor and the block is 0.2. A horizontal force of 10 N is applied on the block as shown in the figure. The magnitude of force of friction (in N) on the block is 10 N 10 kg
A computer is protected against impact by foam packaging (spring stiffness, k = 100 N/cm; mass, m = 11 kg, including packaging). The maximum acceleration that the computer can withstand on impact with a hard surface is 4g. At the maximum acceptable impact acceleration, how much does the packaging compress upon impact? Give the answer in cm. What is the maximum height, h, in cm that the case can fall from without damaging the computer?
1:E1 A docs.google.com/for Untitled Section Determine the force P required to lower the 40-kg cylinder at a slow steady speed. The coefficient or friction between the cord and its supporting surface is 0.30. (g-10 m/s³). 40 kg Your answer If (4, =0.4) then the o between the normal force N and the friction force F will be Your answer العربية الإنجليزية III
Khufra works at a spring factory and he was assigned to test a certain spring, whose constant is 50 N/m attached to a 50-kg block in an incline (©=30°). With the spring initially at equilibrium position, the block was pushed 0.3 meters up the incline by a 50-N external force applied parallel to the path. The coefficient of kinetic friction is 0.30. d) How much work is done by the block (in Joules) on the spring? e) How much work is done by the applied push on the block? f) How much work is done by friction?
Qs: Two blocks are connected by a string. Block 1 is on a frictionless surface, while block 2 hangs freely. The string passes over a massless frictionless pulley. Find the acceleration of block 1, if the acceleration of block 2 is equal to 3.8m/s², and the tension in the string. 2.2 Kg 1.4 Kg
in the following figure, the horizontal surface on which this block slides is frictionless. If the two forces acting on it each have magnitude F = 34.0 N, and M = 14.0 kg, what is the magnitude of the resulting acceleration of the block (in m/s?) 30° M
A cigarettes dispenser requires a south African five-rand (R5) coin with a mass of 9.5 g to dispense one cigarette with a mass of 0.2 g. The design of such a cigarette dispenser is based on a helical spring, of negligible mass, which is found to extend 0.1 mm under a mass of 0.2 g. The spring can support a total mass of a coin. As the customer place money on the dispenser, the spring and coin system displace vertically through 4 mm and release. 1.1. Provide a schematic representation of the mass and spring system. 1.2. Calculate the frequency of natural vibration of the dispenser. 1.3. Determine the velocity of the coin when it is 2 mm below its resting position.