A block diagram of a system consisting of a sinusoidal voltage source, an RLC series bandpass filter, and a load is shown in the figure. The internal impedance of the sinusoidal source is 80 + j0 N, and the impedance of the load is 480 + jo N. The RLC series bandpass filter has a 25 nF capacitor, a center frequency of 49 krad/s, and a quality factor of 6.55. (Figure 1) Figure 1 of 1 >

A block diagram of a system consisting of a sinusoidal voltage source, an RLC series bandpass filter, and a load is shown in the figure. The internal impedance of the sinusoidal source is 80 + j0 N, and the impedance of the load is 480 + jo N. The RLC series bandpass filter has a 25 nF capacitor, a center frequency of 49 krad/s, and a quality factor of 6.55. (Figure 1) Figure 1 of 1 >

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter24: Resistive-inductive-capacitive Parallel Circuits

Section: Chapter Questions

Problem 4RQ: A tank circuit contains a capacitor and an inductor that produce 30 of reactance at the resonant...

See similar textbooks

Similar questions

An RC low-pass filter is shown in the figure. Its purpose is to attenuate higher frequencies while allowing lower frequencies to pass through. A 960-Hz sine-wave signal with rms amplitude of Vrms = 1.9 V is fed into the filter. The values of the components are R = 120 Ω and C = 0.64 μF and Vout-rms = 1.724 V. By what angle, in degrees, does the output voltage lag the input voltage?
Calculate the bandwidth in kHz Blank 1 and an inductor's Q Blank 2 at100MHz. It has an inductance of 6mH and a series resistance of 1.2k2.
Identify the reason for a nonsinusoidal signal being distorted when it passes through a filter. -The distortion occurs because harmonics are removed or rejected, leaving a different waveshape. -The distortion occurs because harmonics are synchronized, leaving a different waveshape. -The distortion occurs because the signal is modulated, leaving a different waveshape. -The distortion occurs because harmonics are added in the filter, leaving a different waveshape.
The below 4 figures are the angle of the transfer function of passive filters. Phase (deg) -45- Phase (deg) (Cep) sid 45 10 10 Frequency (radisec) 10² Frequency (rad/sec) Figure-1 shows the frequency response of Figure-2 shows the frequency response of Figure-3 shows the frequency response of Figure-4 shows the frequency response of 4) ( + 4 10 10" 10
30. Realize the imego phase fiteo with tue impulse desponse - hon) = son) + Scn-+) - son2) + scna)+SCny) %3D
A parallel R-L-C circuit is fed by a constant current source of variable frequency. The circuit resonates at 100 kHz and the Q-factor measured at this frequency is 5. Find the frequencies at which the amplitude of the voltage across the circuit falls to (a) 70.7% (b) 50% of the resonant frequency amplitude.
HW: Determine Zin, Zo and the small-signal voltage gain. P type C₁ C₂ Vo D Vin Rs RD RL SINT 4k 2k 4k Zin -5V Zo +5V = kp 1mA/V2 Vr = -0.8V λ=0 Bobin painleido XL=SL = jwL Frequency Response Sm= 2 kp (VSG₂Q +VT) rd = 1 A IDQ ID= kp (VSC₂+V+) ² notion Xc = Copacite 1 (WC 345
Describe what happens to the current in this RC series circuit as the frequency increases. Explain in general terms why the observed change should occur.
Consider the circult given below a) Identify the circuit with details b) Find the Q-point O Find Vs,Vs Vo, Vos and Vas d) Find the RMS output voltage and draw it In the same graph- with Input e) Comment on the output signal if the input increases to Vinp=20V V 18 V 2.7 w - 10 MA atanm - - 6 V C 100F -0.3 F 1.5 MD - 130 F 220 11
Write the name of the filter that matches the description below.
H.W: A resistor of resistance R-1000 2 is maintained at 17 °C and it shunted by 100 uH inductor. Determine the rms noise voltage across the inductor over a frequency bandwidth of: i) 15.9 kHz Ans: 182 x109 volt ii) iii) Ans: 9.22 x10-8 volt Ans: 2.34 x10-6 volt 159 kHz 1590 kHz
You are an electrician working in a plant. A series resonant circuit is to be used to produce a high voltage at a frequency of 400 Hz. The inductor has an inductance of 15 mH and a wire resistance of 2 . How much capacitance should be connected in series with the inductor to produce a resonant circuit? The voltage supplied to the circuit is 240 V at 400 Hz. What is the minimum voltage rating of the capacitor?