A beam with a half-circular cross-section with radius R = 1.7 in is subjected to a maximum positive bending moment of 25700 lb in about a horizontal axis. Determine the maximum tensile and compressive flexural stress in the beam. Denote a tensile stress with a positive number, and a compressive stress with a negative number. psi psi o max R o maxc

A beam with a half-circular cross-section with radius R = 1.7 in is subjected to a maximum positive bending moment of 25700 lb in about a horizontal axis. Determine the maximum tensile and compressive flexural stress in the beam. Denote a tensile stress with a positive number, and a compressive stress with a negative number. psi psi o max R o maxc

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.10.17P

See similar textbooks

Similar questions

The Z-section of Example D-7 is subjected to M = 5 kN · m, as shown. Determine the orientation of the neutral axis and calculate the maximum tensile stress c1and maximum compressive stress ocin the beam. Use the following numerical data: height; = 200 mm, width ft = 90 mm, constant thickness a = 15 mm, and B = 19.2e. Use = 32.6 × 106 mm4 and I2= 2.4 × 10e mm4 from Example D-7
A beam supporting a uniform load of intensity q throughout its length rests on pistons at points A, C and B (sec figure). The cylinders are filled with oil and are connected by a tube so that the oil pressure on each piston is the same. The pistons at A and B have diameter d1and the piston at C has diameter D2. (a) Determine the ratio of d2to d1so that the largest bending moment in the beam is as small as possible. Under these optimum conditions, what is the largest bending moment Mmaxin the beam? What is the difference in elevation between point C and the end supports?
What is the maximum length of a uniformly loaded, simply supported beam based on the maximum allowable stresses, its normal stress of 90MPa and its shear stress of 100MPa? The uniform load is 10kN/m. The area is b = 20mm and h = 80mm
MA MB= Mc= MD= Required information For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment diagrams. V=50 lbf/in and V2 = 7 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Hinge = 1400 lbf/ A BI AC R₂ R₁ 4 in 4 in 2 in V1 Determine the values of the moments at points A, B, C, and D. lbf.in lbf.in lbf.in Ibf.in V2 D R₂
The composite beam is made of steel (A) bonded to brass (B) and has the cross section shown in Figure 2. If it is subjected to a moment of M = 6.5 kN.m, determine the maximum bending stress in the brass and steel. Also, what is the stress in each material at the seam where they are bonded together? The elastic modulus for the brass is EBrass = 100 GPa and the elastic modulus for the steel is Esteel = 200GPa. 150 mm B N M 175 mm 200 mm X
The composite beam is made of steel (A) bonded to brass (B) and has the cross section shown in Figure 2. If it is subjected to a moment of M= 6.5 kN.m, determine the maximum bending stress in the brass and steel. Also, what is the stress in each material at the seam where they are bonded together? The elastic modulus for the brass is EBrass = 100 GPa and the elastic modulus for the steel is Esteel = 200GPa. 150 mm B N M 175 mm Figure 2 200 mm
A leaf spring 75 cm long is required to carry a central load of 8 kN. If the central deflection is not to exceed 2 cm and bending stress no greater than 200 MPa, determine the thickness, width and number of plates. Also compute the radius to which plates should be curved. As- sume width of plate to be 12 times its thickness and E = 200 GPa.
From the given figure below, determine the fiber stress of the beam located at 50mm from the top of the beam at point C if it has a cross section of 200mm wide by 350mm deep. 20KN 40KN Thi A k 65kN/m P RB=320kN 280KN V -40kn -80kNm 4m 20KN qu 520 kNm RD = 260KN V-DIAG -260kN A M-DIAG
Find the maximum shear force (V), the cross section can carry if the maximum shear stress is not to exceed 100MPa. And then after calculating the value of V, FIND the force carried by the web. 200 mm 20mm 20mm V 210mm 20mm 110mm
Question 1-2) F=22 kN single load, M=23 kN.m moment and w=17 kN/m distributed load are acting on the beam whose loading condition is given in the figure . The length L is also given as L=3 m . The cross-sectional properties of the beam are; body height y g =223 mm , body thickness x g =11 mm , flange width x f = 170 mm , flange height y f =18 mm . Point E on the section is located just below the flange-body junction. It is desired to determine the stress state in the section taken from the C level of the beam. According to this; Question 1-F) For a section taken from the C point of the beam; Find the shear stress at point E on the beam section due to the shear force . ( Write your result in MPa .) Question 1-H) For a section taken from the C point of the beam; Find the normal stress that occurs at point E on the beam section due to the normal force . ( Write your result in MPa .)
Picture given below; There is a uniformly distributed load on the beam, which is made of Al2010 (T4) alloy T-profile and is connected to the "A" sliding bearing with "B" joint fixed support. Safe compression and tensile normal stress of the beam is Gemn=100 MPa. q=23 kN/m C-C Kesiti + 15 | 18 | 15 q=23 kN/m A유 30 cm 100 cm 150 cm 16 KİRİŞ T- PROFİLİ 74 Ød MAFSAL PİMİ Ölçüler mm dir. 104 S-1) Calculate the support reactions by drawing the SCD of the beam. S-2) The beam; a) Draw the shear force diagram, b) Moment diagram and determine the maximum moment. S-3) Find the x and y axis coordinates of the center of gravity of the cross-sectional area of the beam whose T-profile dimensions are given. S-4) Find the moments of inertia with respect to the vertical and horizontal axes passing through the center of gravity of the T-profile cross-section area. S-5) Find the tensile and compression stresses caused by bending on the beam with T-profile and check the safe carrying condition of this…
In the figure shown, the aluminum strut has a cross-sectional area in the form of a cross. If it is subjected to the moment M= 8 kN.m: 1) determine the bending stress acting at points A and B, 2) show the results acting on a stress distribution diagram.