(a) Based on the figure, give the minimum and the maximum of the external load, P. (b) Based on the figure, give the stiffness coefficient of the joint and the pre-load. (c) Draw and annotate the force load diagram with F, and Fm on the vertical axis and P on the horizontal axis. (d) When the load is at Pmar, determine the load factor with respect to joint separation. (e) Assume that the proof load, Fp, is 7500 lbf. When the load is at Pmaz, determine the load factor with respect to overproofing. mar;

(a) Based on the figure, give the minimum and the maximum of the external load, P. (b) Based on the figure, give the stiffness coefficient of the joint and the pre-load. (c) Draw and annotate the force load diagram with F, and Fm on the vertical axis and P on the horizontal axis. (d) When the load is at Pmar, determine the load factor with respect to joint separation. (e) Assume that the proof load, Fp, is 7500 lbf. When the load is at Pmaz, determine the load factor with respect to overproofing. mar;

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please explain and provide solution
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; / = 1950 in.“). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 190 kip-ft, P = 26 kips, LAB = 8.6 ft, LBc = 12.9 ft. P MA LAB LBC Answer: (a) VA = in. (b) VB = in.
W A L Test beam Strain gauge (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. Section A-A Strain gauge 1 b Strain gauge 3 Strain gauge 2 B (b) Location of Huggenberger strain gauges a Referring to the above figure, calculate the location of the centroid, the second moments and product of area for the cross-section if; • D = 67 mm B = 41 mm t = 2.41 mm. From these, calculate the position and orientation of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis). Also calculate the directions of the principal second moments of area. Next, graph as scale diagram of the cross-section and plot the neutral axis on that diagram in the correct location and indicate the direction of deflection for the same conditions
Problem- A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18 mm, respectively. An axial load of 12kN is applied on the bar. E= 2 × 10 N/mm². The elongation of the bar will be
Solve the problem below and show your complete, systematic and neat solution with explanation.
Identify the equation for the deflection at point C.
a.) A 3-m height concrete column is reinforced with 4 steel reinforcement bars, each bar with a 25 mm diameter. Determine the normal stresses in the concrete and steel when an axial centric force of P = 660 kN is applied to the column. Determine also the shortening of the column. The modulus of elasticity of the concrete and steel has values of Ec = 26 GPa and Es=200 GPa The cross section of the column is shown in the figure. b.) If the steel reinforcement bars are to resist at least 1/3 of the applied load, calculate the minimum amount of area of steel reinforcement bars required. What is the minimum of number of 25 mm diameter bar required? P = 660 kN 3 m 200 mm 200 mm
Consider the nonprismatic cantilever beam of circular cross section shown. The beam has an internal cylindrical hole in segment 1; the bar is solid (radius r ) in segment 2. The beam is loaded by a downward traingular load with maximum intensity qo as shown. Linear q(x) 2 M1 2 2c Segment 1 Segment 2 0.5 EI El (a) Find expression for maximum compressive stress at point 1. (b) Find expression for maximum tensile stress at point 1.
1. A stepped shaft is shown, the region AB is aluminum having G = 28 GPa, and the region BC is steel, having G= 80 GPa. The aluminum portion is of solid circular cross section 45 mm diameter, and the steel region is circular with 60 mm outside diameter and 30 mm inside diameter. A clockwise torsional load of 4000 N-m is applied at B, assume ends A and Care rigidly clamped. De termine the following: a. maximum shearing stress in the aluminum b. maximum she aring stress in the steel (
i need the answer quickly
The shaft AB is formed by bonding steel tube and a brass core. Outer diameter of the steel tube is 60 mm and the diameter of the brass core is 30 mm. The shaft is subjected to uniform distributed torque o t kNm/m. The allowable shear stresses for steel and brass are (Tsteel)all = 80 MPa and (Tbrass)all = 50 MPa, respectively. Determine a) the maximum value of the uniform torque t , b) the corresponding angle of twist at A. (The shear modulus for steel and brass are Gsteel = 77 GPa and Gbrass = 40 GPa, respectively) - Steel Tube A t kNm/m B 30 mm 15 mm 1 m 1 m Brass Core Cross Section
The hollow circular beam is fixed to the wall (with a bracket) on the left and has an end-cap on the right. The cross-section is shown. (a) Determine state of stress at point A & draw the stress element (b) Determine state of stress at point B & draw the stress element A 100 k-in Tout 2 in n=1.75 in В. B 40 k-in C Tout 30 k X