A balanced load of phase resistance 36 andcapacitive reactance of 40 2 is connected in starconfiguration. The load side phase voltage is 255 V.Compute the magnitude of: a) Po; b) P30;

Given data: Phase voltage at load: Vphase=255 VZphase=36-40j

Answered: A balanced load of phase resistance 36…

A balanced load of phase resistance 36 and capacitive reactance of 40 is connected in star configuration. The load side phase voltage is 255 V Compute the magnitude of: a) Po; b) P30 ;

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: 16 A 5 x 4.0 cm² laminated magnetic core has a flux of 5 mWb. Assuming a fringing factor of 1.125,…

Q: Draw the following functions: 1-Y=X - [X]; for -2 < x < 2

Q: 1A (A ww 3Ω + 8F VC - The circuit above is in DC steady state. What is the value of v, in volts? 5Ω

Q: choose the correct expression for (A + B C D O A+B+CD B + C + D B + C + D A B + C + D A OA ||

A: Given a Boolean expression, F=A+B¯.C.D¯

Q: 8 The EMF induced in the secondary winding of a 50 Hz single-phase transformer having 500 turns on…

A: Given: The EMF induced in the secondary winding, E2=13.2 kV Frequency, f = 50 Hz Number of turns on…

Q: Consider the unity negative feedback discrete system with digital PID controller. If the transfer…

Q: 4- A system with a state matrix A = a- critical damped b- over damped 5- A system with input matrix…

Q: d. Determine the value of Vs Vs 11 5mA R1 5000 V2 6V R3 1.0KQ V1 -12 V R2 3.0k

A: Given circuit,

Q: A 220 V dc shunt motor draws a current of 50 A from the supply and runs at 900 rpm. Its armature and…

Q: Fig. shows the single line diagram of a 3-phase system. The percentage reactance of each alternator…

Q: 16V +1 www 4Ω 8H ₁₁ The circuit above is in DC steady state. What is the value of it in amps? www…

Q: μA, and Vp = 10 V. a.4) At what anode voltage (VA) will each PUT in Figure 2-11 begin to conduct?…

Q: In the network below, find the power associated to the current source, for V1 = 7 V. 24 elect one:…

A: Given circuit: For, V1=7 V.

Q: Determine whether the following signals are energy, power, or neither energy nor power.

Q: 13. If the percentage reactance of the system upto the fault point is 20% and base kVA is 10,000,…

A: Given, Percentage reactance of the system up to fault point, % X=20 % Base kVA rating is 10,000 kVA.

Q: Which electrical component can rectify AC current into DC current? a) p-type semiconductor b) diode…

A: Given , The component which can rectify AC Current into Dc Current is....

Q: Determine whether or not each of the following signals is periodic. If a signal is periodic,…

Q: In the circuit shown below each resistor are 10052. If the battery has 30 V potential differences…

Q: - V₁ 7 √√3+√√₂ =0 - (20) 1₂a + (65) Fon + (7) ₁₂ = 0 20 -62 F.A 7.02 -212 +61 + 710 =0 @ + Uke…

A: Given:

Q: 6. If the rms current through a 4.7 kn resistor is 4 mA, the peak voltage drop across the resistor…

A: The peak voltage is the maximum voltage of the input and the rms voltage is the average voltage of…

Q: 1. A 70-Vac source has the following waveform. Determine: a. Vpk b. Vpk-pk C. Vrms d. Period e.…

A: Given a 70V AC source waveform (Vrms = 70V) Asked for the following Vpk Vpk-pk Vrms Period…

Q: The current in the circuit shown in the figure is 0.20 A. What is the potential difference AVat…

A: Given circuit: Current, I=0.20 A. Resistance, R=30 Ω Applied voltage through battery, ∆Vbat=?

Q: 10 Given a common magnetic core whose length is 100 cm, its cross-sectional area is 25 cm square.…

Q: c. if f(w) = f(x)e-izda, find the Fourier Transform of f(z) Jezix f(x) = 0 if -2<x<2 Otherwise

Q: Question: 2 Tp.u(s) T₁₂ (8) = 3²7 +35 This process is controlled by a P controller with gain Kc = 3.…

A: The given process transfer function is Tpus=2s2+3s. Gain of the P-controller is Kc=3. Sensor and…

Q: Determine whether the following signals are energy, power, or neither energy nor power.

Q: Use the duality property to find the inverse transforms of the following functions: F(w) 10u(w) - 5…

A: Since you have posted the multiple questions so we are supposed to answer the 1st one.

Q: Q8 a) b) Find and sketch o(t) = f(t)* f(t) for the pairs of functions shown as follow: B : (1) 1₁…

Q: The magnetic flux passing perpendicular to the plane of the coil and directed into paper (See Fig.…

A: We have been given that magnetic flux perpendicular to the plane of the coil and directed into the…

Q: 67. In a short circuit test on a circuit breaker, the following readings were obtained on single…

A: Given a short circuit test on a circuit breaker having, Time to reach the peak restriking voltage =…

Q: calculate the gate input of F=AB + C(D+E)

A: Given: F=AB + C(D+E) To calculate: the gate input of F

Q: SKILL BUILDING ACTIVITY # 1 Write the AM voltage equation for a 120 Vp, 700 KHz carrier and a 100…

A: Since you have posted the multiple questions so we are supposed to answer the 1st one.

Q: IN THE PULL UP PHASE OF NARROW GRIP PULL UP EXERCISE : Look for excessive joint torques produced…

A: Step:1 Muscles, bones, and joints of arms exert some forces during exercises. Muscles exert far…

Q: PRACTICE 7.9 If vc (t) = 4 cos 105t V in the circuit in Fig. 7.26, find v¸ (t). Ans: -2.4 cos 10ºt…

Q: The Fig. shows the part of a typical power system. If for the discrimination, the time grading…

Q: QUESTION 8 What electronic element can be used as the switching device for a 120 VAC discrete output…

A: Ans: Triac PLC outputs are of two general types: Relay and Solid state Relay outputs are…

Q: A 6 pole, 50 Hz, 3 phase, star connected motor has an impedance of 0.016 ohm and a fixed time…

Q: Q2. For the circuit as shown below, find a single equivalent inductor at terminals (a, b), where…

A: Given a circuit with series and parallel combination of inductors Asked to find equivalent…

Q: choose the correct expression for A + A B C : °A + Вс ОB+A C O B + AC C+ AB

A: Given logic expression, F=A+A.B.C

Q: For the system shown in Fig. 1, the system has a transmission line of unknown length and unknown…

A: The output impedance, or opposition to current flow, refers to the impedance of the component that…

Q: A 100 kVA, 220/440 V, 50 Hz power transformer is tested at 75 Hz to evaluate the core los while its…

A: Given, A 100 kVA, 220/440 V, 50 Hz power transformer is tested at 75 Hz to evaluate the core loss,.…

Q: . A Si diode at a temperature of 25°C has VD = 0.7V at Is = 10nA. The temperature is raised to…

Q: Given the difference equation: y(n) = 0.2y(n-1) + 0.2y(n − 2) + 0.1u(n-1) 1-Find the discrete…

A: Given the difference equation, yn=0.2yn-1+0.2yn-2+0.1un-1 To find: 1) Find the discrete transfer…

Q: find F.T the? f(t) = u(t) cos wot let u(t) = TS (W) + J W coswot = πTES (W_Wo +8 (W+wo)

Q: C₁ = [0.05P2 + 20P₂ + 30]; $ hr C₂ = [0.056P2 + 15P₂ +40]; hr Here P₁ and P₂ are in MW. Each…

Q: Logic Circuits and Switching Theory Research on the relation of metastability to memory elements.…

A: ANSWER METASTABILITY---> In…

Q: Use nodal analysis to determine each of the circuit parameters for the provided circuit

A: The circuit is shown below: Using the nodal analysis, VA=40 VVC=10 VVB-VAR1+VBR3+VB-VCR2=0

Q: PROBLEM Consider a parallel connection of two subsystems shown below U(S) 1 s+1 3 s+4 Obtain the…

A: Given: Parallel connection of two subsystems is shown,

Q: Find the value of current I in given figure

Q: The output modules cannot handle as much current per output The input modules cannot handle as much…

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

A balanced load of phase resistance 36 and
capacitive reactance of 40 2 is connected in star
configuration. The load side phase voltage is 255 V.
Compute the magnitude of: a) Po; b) P30;

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
A DC-DC Chopper Circuit with an RL Load has an output current waveform shown below with a duty cycle of 50% and 1ms period. If it has a resistance of 1ohm and an inductance of 10mH, find the source voltage. 5A 2A ton toff output _current
A DC-DC Chopper Circuit with an RL Load has an output current waveform shown below with a duty cycle of 50% and 1ms period. If it has a resistance of lohm and an inductance of 10mH, find the source voltage. output 5A -current 2A ten toff
Quistion.4. a) A sinusoidal voltage is applied to the resistive circuit in figure.Q.4. a. Determine the following: i. Ims ii. Iavg iii. Ip iv. Ipp 10V 1.0 ΚΩ Figure.Q.4.a
9. A noninductive load with a resistance of 30 Q2 is connected in series with a capacitor. The capacitor has a capacitive reactance of 25 Q and negligible resistance. The series circuit is energized from a 210 V, 60 Hz source. Determine: a. the impedance of the series circuit. b. the current, in amperes. c. the loss in volts across the noninductive resistance load. d. the loss in volts across the capacitor.
A 230 V, 50 Hz a.c. supply is applied to a coil of 0.06 H inductance and 2.5 resistance connected in series with a 6.8 F capacitor. Calculate impedance and power consumption and power factor. Now ,In above a.c. circuit, A inductor of 0.2H is connected in parallel with the power supply, find new power factor and power consumption.
13. Susceptance and conductance add to form.A. Impedance.B. Inductance.C. Reactance.D. Admittance.
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
4) Determine the value of voltage across resistor and capacitor5) Convert in rms values
An inductor of 150hms and resistance of 10 Ohms are connected in series to a 230V, 50 Hz ac supply. Determine the active and reactive power and power factor in the circuit.
A chopper circuit has an inductive load of 2ohm resistance and 10mH inductance. If the source voltage is 20 V and the frequency of the chopper is set to 100Hz and the on-time to 5 ms. Determine the average voltage and current, maximum and minimum load currents.
2. Refer to the Figure 2. a) Determine the total impedance of the circuit in polar form. b) Determine the voltage v(t) and current i(t) sinusoidal forms. Sketch one cycle of the waveforms in the same x-axis. Clearly indicating the peak value and the period of each waveform and the phase difference (in milliseconds) between the two waveforms. c) Determine the values of resistance R and inductance L. d) Determine the phasors V,, VR and Vc. e) Sketch the phasor diagram showing Vs, Vr, Vr, Vc and I.