• A 6 MW generator had a thrust of 103,000 lb. The outside diameter of the step bearing is 12 in, and the inside diameter is 8 in. Employ a film thickness of 0.004 in. Use SAE 20 oil at 120, the specific heat of the oil being 0.6 BTU/lb deg F, and density of 0.307 lb/cu. in Determine: (a) the flow rate in gallons / minute

• A 6 MW generator had a thrust of 103,000 lb. The outside diameter of the step bearing is 12 in, and the inside diameter is 8 in. Employ a film thickness of 0.004 in. Use SAE 20 oil at 120, the specific heat of the oil being 0.6 BTU/lb deg F, and density of 0.307 lb/cu. in Determine: (a) the flow rate in gallons / minute

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Similar questions

• A 6 MW generator had a thrust of 103,000 lb. The outside diameter of the step bearing is 12 in, and the inside diameter is 8 in. Employ a film thickness of 0.004 in. Use SAE 20 oil at 120 , the specific heat of the oil being 0.6 BTU/lb deg F, and density of 0.307 lb/cu. in Determine: (d) Temperature rise
Compute the power in KW generated by Agusan Hydro Bectric power plant with water flOH rate of 1,552 liters/sec and net head loss of 10% with total efficiency of 89 59% 5.5 KW B. 75 KW 9.8 KW 12.3 KW
1. A LEV system has a centrifugal fan rotating at 714 rpm. The airflow is 6210 cfm, the fan total pressure is 4.07” w.g., and the brake horsepower is 3.12 hp. If the rotating speed is decreased to 620 rpm, what are the brake horsepower? a. 1.43 hp b. 2.04 hp c. 2.41 hp d. 2.67 hp 2.A LEV system has a centrifugal fan rotating at 714 rpm. The airflow is 6210 cfm, the fan total pressure is 4.07” w.g., and the brake horsepower is 3.12 hp. If the rotating speed is decreased to 620 rpm, what are the new value for fan total pressure? 4.15" w.g. 3.87" w.g. 3.07" w.g. 3.94" w.g.
Please no written by hand solutions A 4-ton heat pump is installed. Desired flow rate is 12 USgpm. The runner and header from the Mechanical room is 110 feet in delivery and 110 feet in return. The fluid running in the system is Methanol-20%. The ground loop consists of three parallel vertical loops each 290 feet in length. The ground loop is made of 0.75" HDPE SDR 11 pipes and the runner-header is made of 1.25" HDPE SDR 11 pipes. The heatpump pressure drop is given 5.8 ft of wc for a flow of 6 gpm of water (Correction factor 20% Propylene Glycol:1.36, 20% Methanol: 1.25, 25% Ethanol: 1.32). Q: Calculate the pressure drop in the Runner-Header. Question 11 options: 9.9 ft of wc 5.8 ft of wc 7.3 ft of wc 3.8 ft of wc 13.4 ft of wc 2.9 ft of wc
A centrifugal pump operating under steady flow conditions delivers 2,270 kg/min of water from an initial pressure of 82,740 Pa to a final pressure of 275,800 Pa. The diameter of the inlet pipe to the pump is 15.24 cm and the diameter of the discharge pipe is 10.16 cm. What is the work done? a. 458.1 kJ/min b. -458.1 kJ/min c. 438.4 kJ/min d. -438.4 kJ/min
Seven hundred gallons per minute of water are being discharged by a centrifugal pump 5 ft above the pump inlet. The inlet pressure is 4-in Hg above the atmospheric and the discharge pressure is 29 psia. If the pump has an 8-in diameter inlet and a 4-in diameter discharge, find the pump efficiency. Assume the pump input is 8Hp.A. 55%B. 64%C. 73%D. 84%
Find the motor size needed to provide the forced-draft service to a boiler thatburns coal at the rate of 10 tons per hour. The air requirements are 59 000 cfm, air isbeing provided under 6 inches water gage by the fan that has mechanical efficiency of 60%. Assume fan to deliver at a total pressure of 6 inches water gage.
P: 50,000 ii. 2m Pa 50mm Pump VALVE P= 175,000 25mm Pa TURBINE P= 40,000 Pa с 25MM The diagram above shows the set up for a pump and water turbine unit at a power generation company in Point Lisas. i. The water has a temperature of 25°C and the head losses accumulated by the valve and fittings is 2 N.m/N between points A and B. If the flow rate is 0.02m³/s and the pump is 75% efficient, determine the power put into the pump. Determine the energy removed by the turbine and use it to determine the mechanical efficiency of the turbine given that 2450W of power is outputted from the turbine.
A Thomas meter is located in an air duct of 2 sq ft cross-sectional area. The air weighs 0.083 lb per cu ft, and its specific heat is 0.24. Assume a controlled temperature differential of 5° and heater potential of 110 volts. Plot the velocity as abscissa and amperage as ordinate for veloc- ity 0 to 300 ft per min. Assume constant amperage of 3, and plot tem- perature difference against velocity. Discuss the curves from the stand- point of accuracy of the system.
A fan require at least 4.5 hp to deliver 18,000 CFM of air running at 320 rpm. For a service factor of 1.15, find the designed horsepower of the sprocket.
A refrigeration cycle operates at a flowrate of 2 lbm/hr, the enthalpy change is h = 4000 BTU/lbm,compute the refrigeration lift (tons). Determine the HP required for the compressor to be used for problem.
8. A pump is moving soybean oil through a l-in. (nominal) pipe. The 110-volt motor is using 285 watts. Assuming an over-all pump and motor efficiency of 65 per cent, what is the pumping rate in gallons per minute if the suction and discharge pressures are, respectively, -5 and 23 lb per sq in.? 9. Carbon dioxide is metered into an air conduit which is 12 sq ft in