A 400V three-phase, four wire system has the following loads connected: Phase 1: load impedance Z1 = 40 + j15 Ω Phase 2: load impedance Z2 = 60 Ω Phase 3: load impedance Z3 = 15 – j20 Ω I am just looking for the working out for phase 2 - please ignore the other phases The line and phase voltages for all phases (including phase angles) The line and phase currents for all phases (including phase angles) The neutral current (including phase angle)

A 400V three-phase, four wire system has the following loads connected: Phase 1: load impedance Z1 = 40 + j15 Ω Phase 2: load impedance Z2 = 60 Ω Phase 3: load impedance Z3 = 15 – j20 Ω I am just looking for the working out for phase 2 - please ignore the other phases The line and phase voltages for all phases (including phase angles) The line and phase currents for all phases (including phase angles) The neutral current (including phase angle)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.43P: Three single-phase transformers, each rated 10MVA,66.4/12.5kV,60Hz, with an equivalent series...

See similar textbooks

Similar questions

Figure 3.32 shows the oneline diagram of a three-phase power system. By selecting a common base of 100 MVA and 22 kV on the generator side, draw an impedance diagram showing all impedances including the load impedance in per-unit. The data are given a follows: G:90MVA22kVx=0.18perunitT1:50MVA22/220kVx=0.10perunitT2:40MVA220/11kVx=0.06perunitT3:40MVA22/110kVx=0.064perunitT4:40MVA110/11kVx=0.08perunitM:66.5MVA10.45kVx=0.185perunit Lines I and 2 have series reactances of 48.4 and 65.43, respectively. At bus 4, the three-phase load absorbs 57 MVA at 10.45 kV and 0.6 power factor lagging.
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
a balanced three phase voltage of 100v line to neutral is applied to a balanced y connected load with undergrounded neutral . the three phase load consists of three mutually coupled reactances. each phase has a series reactance of Zs=j12 ohm and the mutual coupling between the phases is Zm=j4. determin the current using symmetrical components
Draw Wye- Delta three phase transformers connection ( no-load and full-load) in Lt-spice
Can you explain the given questions in an original way? Single Phase and Three Phase Principles • Single Phase Generators • Two Phase Generators
A three-phase circuit is balanced. The source voltage for the a-phase has a magnitude of 100 volts, and you can assume the phase angle is a reference of 0 degrees. Write the phasor expressions with proper subscript notation for the source voltage for each leg of the three-phase source if it is in a positive phase sequence.
Differentiate Wye and Delta Connection in Three Phase System and Relate it with Computer Engineering
In a three-phase system the per-unit phase voltages are 100° , Vôn = 0.8Z180° Van 0.920° , Von = 0.92 - а What are the per-unit symmetrical components V0) and V)? Express in polar notation.
X₂=0.1 1 XL +03 Soto X₁ = 0.2 X = 0.1 X = 0.1 Above is the one-line diagram of a simple power system. Each generator is represented by an emf behind the subtransient reactance. All impedances are expressed in per unit on a common base. All resistances and shunt capacitance are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. A symmetrical fault occurs at bus 1 through a fault impedance Z, =j0.08 per unit. a) Using Thevenin's Theorem, determine the impedance to the point of fault and the fault current in per unit. b) Find the bus voltages and line currents during the fault. 2 O oto
Discuss how delta connection is achieved in three-phase systems?
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator2. “Reactive power in a system is dissipated generally as thermal energy?”A. TRUEB. FALSE3. Which of the following statements are correct for three phase circuit:A. Sum of all the three phase currents is zero in unbalanced networkB. Total power transfer to load is constant with timeC. Neutral conductor is same size in terms of material used as in single phase conductorsD. Net apparent power consumed is equal to real power
In the three-phase system shown in the figure, phase a is on no load and phases b and C are short-circuited to ground Ia = 0 In Ie The following currents are given: I, = 91.656 Z160.9° I, = 60.006 Z90° Find the symmetrical components of current 1,, I, and 1, .