A-3-phase transmission line is shown in figure:AV₂AV bAVC-AV₂-1-=-AV-aIVoltage drop across the transmission line is givenby the following equation:IZ₂ Zm ZmZm Zs ZmZm Zm Zs][IaIbCShunt capacitance of the line can be neglect. Ifthe line has positive sequence impedance of 15 Nand zero sequence impedance of 48 , then thevalues of Z, and Zm will be

Given- A 3-phase transmission line The shunt capacitance of the line can be neglected. +ve sequence…

A-3-phase transmission line is shown in figure: -AVA AV a AVb ΔV. -AV₂- -AV H I a I₂ Voltage drop across the transmission line is given by the following equation : I Zm Zs Zm Zm Zm Zs Zm Zm Zs 10 Ia Ib Ic Shunt capacitance of the line can be neglect. If the line has positive sequence impedance of 15 and zero sequence impedance of 48 №, then the values of Z, and Zm will be

A-3-phase transmission line is shown in figure: -AVA AV a AVb ΔV. -AV₂- -AV H I a I₂ Voltage drop across the transmission line is given by the following equation : I Zm Zs Zm Zm Zm Zs Zm Zm Zs 10 Ia Ib Ic Shunt capacitance of the line can be neglect. If the line has positive sequence impedance of 15 and zero sequence impedance of 48 №, then the values of Z, and Zm will be

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
A surge of 100 kV travels along an overhead line towards its junction with a cable. The surge impedance for the overhead line and cable are 400 ohms and 50 ohms respectively. The magnitude of the surge transmitted through the cable is ?
Problem 4- A large 3-phase industrial load draws 3.6 MVA at 0.85 power factor lagging from through a three- phase 12.47/7.2 kV 3-wire overhead distribution line. The phase conductor is #1 ACSR “Robin". Taking 3.6 MVA and 12.47 kV as base values, determine (a) The base impedance in (N) (b) The reactive power drawn by the load (p.u.) (c) The total current (p.u.) drawn from the power supply
Consider the 500 kV, three phase bundled conductor line as shown in the figure below. Find the line to neutral capacitance. 0.5 m 30 mm (0) (O to Ine 15 m 15 m
Paragraph Styles The power factor must be close to in the transmission lines will be reduced To insure that losses D(Ctrl) -
Quest- A single phase 50 Hz, system supplies an inductive load of 5000 kw at power factor 0.8 lag through a line 25 km. Resistance of the line is 0.0195 2/km and inductance = 0.36 mH/km, receiving end voltage is 10 kV. A capacitor is connected across the load to get the voltage regulation of 10%. Ratio of transmission line loss with and without shunt capacitor is
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
For transferring electrical power at 220 kV, six conductors of ACSR Drake constitute a 60Hz double circuit three phase line arranged as shown below. The vertical spacing between consecutive conductors is 14ft; the longer horizontal distance is 32ft whereas the shorter horizontal distance is 25ft. a. Find the inductance per phase per mile and the inductive reactance per phase in ohms per mile. b. Find the capacitive reactance to neutral in ohm-miles. c. Find the resistance per phase per mile in ohms per miles. d. If the length of the line is 90 miles then draw an equivalent circuit of the line and analyse the open circuit and short circuit performance of the line. e. Find the maximum power we can transmit over the line. f. If the line is delivering power to a load of 20MW at 0.8 power factor lagging then find the voltage at the receiving end of the line. Also, Determine the voltage regulation, losses and efficiency of the line. g. If a fixed shunt compensation of 3 MVAr is attached at…
Shown are two buses connected via a transmission line. Connected to Bus 1 is a generator(modelled as a voltage source V1), and to Bus 2 is a generator( with Voltage V2) and a load. The line impedance Z = R + jX is not known. Three-phase load is forecasted as 100MW + 60MVar. Generator at Bus 2 is scheduled to deliver 40MW and its excitation is adjusted for the machine to deliver 55 MVar. Voltage at Bus 1 is 241 KV angle 10 deg, while voltage at bus is 230 kV; use V2 as the reference for all angles. 1. What is the current (RMS) in amperes drawn by the load connected to Bus 2? 2. How much real power (in MW) is delivered by the generator connected to Bus 1? 3. What is the total real power loss along the line, in percent of the load? 4. What is the X/R Ratio of the line impedance?
Each line of a 3-phase system given in figure is suspended by a string of 5 identical disks and the ratio of C1/C=0.1 (Shunt capacitance per self-capacitance) is given. If the string is connected to line of voltage 33kV. a) What is the voltage distribution over the unit of string and what is the string efficiency? b) When the string is supplied by a Guard Ring and this lead to add a two air capacitance of value 0.2C, 0.1C respectively to the nearest to the conductor. Find the new voltage distribution and the new efficiency.
A loss less TiL with characteristic impedance of to is terminated in Zr=3Z0. use crank diagram to sketch the voltage versus distance from the load, (Assume vst = 1 volt). @ Repeat the above How for Zv=Zo/3-
The Power transfer capability of transmission line is most affected by: it) shunt conductance b) capacitance c) Resistance. d) inductance