A 2.2 KVA, 480/4800-V, 50 Hz, single-phase transformer is tested with the following results. Find the impedance referred to the HVS of the transformer. SCT measured from LVS Vsc = 24 V SC Isc = 4.5 A PSC = 36 W Select one: a. Rcp = 1.80, and XM,p = 5.03 O b. None Oc. Reqs = 180, and Xeqs = 503 O d. Reqs =1.82, and Xeqs = 5.03

A 2.2 KVA, 480/4800-V, 50 Hz, single-phase transformer is tested with the following results. Find the impedance referred to the HVS of the transformer. SCT measured from LVS Vsc = 24 V SC Isc = 4.5 A PSC = 36 W Select one: a. Rcp = 1.80, and XM,p = 5.03 O b. None Oc. Reqs = 180, and Xeqs = 503 O d. Reqs =1.82, and Xeqs = 5.03

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.16P: A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters:...

See similar textbooks

Similar questions

An ideal transformer has no real or reactive power loss. (a) True (b) False
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1
all äabl (CME 446) 1 If F3=0.1 and Z3=45 Q, then the impedance of the next stage in the multi-section transformer is: of O a. 40.5 stion O b. 49.5 O C. 55 O d. None O e. 36.8 s page Next page
With base MVA of 150 and base voltage of 33. If the reactance of the transformer is 0.23 pu. The parameter of the reactance of the transformer in the Neplan software is O 1.66 2.30 23 0.23 O Non of them
A single-phase transformer has a voltage ratio on open circuit of 7900/660 V. The primary and secondary resistances are 0.55 ohm and 0.035 ohm respectively. The corresponding leakage reactances being 4.22 ohm and 0.18 ohm. The load is equivalent to a coil of resistance 3.85 ohm and inductive reactance of 4.2 ohm. Determine the terminal voltage of the transformer and the output in kW when supplying a given load using approximate equivalent circuit when the applied voltage is 7912 V. Your answer
6. A single-phase, 225-kVA, 460/120-V transformer has 6% impedance and 96% efficiency. Find its series Rand X in percent and in ohms looking from the HV side source. 7. Determine the rms fanlt currents on both sides of a 100-IVA single nhase
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
Draw the full-wave voltage doubler circuit diagram. When a 1:4 transformer is used in this circuit andIf Vo=12sin(314t) alternative signal is obtained at the output, the frequency of the input signal, maximum and rmsCalculate its value.
7. The primary of a single-phase transformer takes 1 A at power factor of 0.4 when connected to a 240-V, 50-Hz supply and the secondary is on open circuit. The number of turns on the primary is twice that on the secondary. A load taking 50 A at a lagging power factor of 0.8 is now connected across the secondary. What is now the value of the primary current ? transformer.) (Neglect the voltage drops in the
3. A 3200/400 single-phase transformer has winding resistance and reactance of 30 and 132 respectively in the primary and 0.0292 and 0.0652 in the secondary. Express these in terms of (a) primary alone, (b) secondary alone. (ans. (a) 4.282, 17.16; (b) 0.067, 0.268)
How does change in frequency affect the operation of a given transformer? Ans. 1. Iron loss........ increases with a decrease in frequency. A 60-Hz transformer will have nearly 11% higher losses when worked on 50Hz instead of 60 Hz. However, when a 25-Hz trans- former is worked on 60 Hz, iron losses are reduced by 25%. 2. Cu loss..........in distribution transformers, it is independent of frequecy. 3. Efficiency...........since Cu loss is unaffected by change in frequency, a given transformer effi- ciency is less at a lower frequency than at a higher one. 4. Regulation........regulation at unity power factor is not affected because IR drop is independent of frequency. Since reactive drop is affected, regulation at low power factors decreases with a decrease in frequency and vice-versa. For example, the regulation of a 25-Hz transformer when operated at 50-Hz and low power factor is much poorer. 5. Heating..........since total loss is greater at a lower frequency, the temperature is…