A 1.5 KVA 50 Hz single-phase transformer has turns ratio 40/50. The primary winding is connected to 230V, 50 Hz supply. Calculate: a. the secondary voltage on no load. b. the maximum value of the flux. c. the value of secondary currents on full load.

A 1.5 KVA 50 Hz single-phase transformer has turns ratio 40/50. The primary winding is connected to 230V, 50 Hz supply. Calculate: a. the secondary voltage on no load. b. the maximum value of the flux. c. the value of secondary currents on full load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11MCQ: For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the...

See similar textbooks

Related questions

Q: A doubly-fed actuator has two windings with current i, at the stator and current i at the rotor as…

A: Given A doubly excited rotating actuator is given.we need to find the correct statement. Please…

Q: A resistor of unknown resistance is in parallel with a 12-2 resistor. A battery of emf 24 V and…

A: circuit is solve as by solve simple parallel connection

Q: Problem#1 Determine vo in the op-amp circuit shown in Fig. 1 6 V 20 ΚΩ 2 V b 40 ΚΩ 2010

A: Given data,

Q: Q2:- a synchronous generator is 25 MVA, 11kV, it is star- connected with the neutral point solidly…

A: Given:X1=X2=0.2puX0=0.08puConsider power base is 25 MVA and voltage base is 11 KVVoltage PU = 1…

Q: In the shown circuit, T= 692 wwwww 252 www 12V 1=039 2H O a a. 0.67 Sec Ob. None of these answers is…

A: Given circuit,

Q: Question 2 This system below is a model of a custom electric heating system: R₁- 120 V R2 1.…

Q: V₂ (s) For the network shown Figure 1, determine the voltage transfer ratio V₁(s) gain, poles and…

A: Applying KCL at V, we get V1s+V-V2(s)1+V-V1(s)1=0 V[s+1+1]=V2(s)+V1(s) V=V1(s)+V2(s)s+2------1 Again…

Q: Using MESH ANALYSIS or Maxwell Method, find the power consumed by each of resistances and determine…

Q: esign a uncontrolled single phase rectifier

A: Rectifier circuit is build up of diodes as the rectifier circuits converts the AC to DC

Q: 7. The system of Figure 9.4 shows a 3-phase Y connected generator feeding a A connected load. If the…

Q: The Synchronizing pulses are transmitted to keep the camera and the picture tube beams in step?…

A: In a monochrome television transmitter, the synchronizing pulses are transmitted to keep the camera…

Q: write the way to find CMRR with all details and needed comprent Notes G₂ you have to draw the…

A: The Common - Mode Rejection Ratio is abbreviated as CMRR. The CMRR of an op-amp is used to identify…

Q: 2. Based on the given figure 2, explain the working principle of the Repeaters. www Long cable w…

A: Repeaters are used in long-distance communication due to inherent noise in the transmission system…

Q: ASAP please recheck the answers, I will like. Using Kirchhoff’s Law, determine the following: a.…

A: Brief description: For the above given question we need to calculate the value of all the current…

Q: 3. A 15-cm diameter circular loop of wire is placed in a 0.50 T magnetic field. (A) When the plane…

Q: Delta-Star Power Transformer 22kV 0.4 kV, Current on 0.4kV side is 1500A CTs on 0.4 kV have ratio of…

A: Given that a delta star 22/0.4kV power transformer. Given CT ratio on 0.4 kV side = 500:1 Current on…

Q: 1. How are encoders used in the measurement of speed? Explain the encoder with a neat diagram.

A: An encoder is a transducer that is used to measure angular displacement. The encoder can be used to…

Q: 3. Draw the zero sequence networks for the system given in figure 3.

Q: H.W. Find the admittance of each set of series elements in Fig. 7. R 1002) R≥6N Xc 80 (a) Fig. 7…

Q: Question 1: Q1- For the sinusoidal waveform in Fig. 1: a. What is the peak value? b. What is the…

A: As per guidelines given to us we can only provide the solution of first three subpart in multi part…

Q: TTPS Output Calculation A thermal station has the following data: Max. demand = 40,000 kW; Load…

A: (i) The boiler and the turbine efficiency of the thermal station are known. The thermal efficiency…

Q: 2. Consider the system: KL(s) = K- (s+1) s² (s+10)(s²+s+1) Draw the complete 180° root locus (K> 0)…

A: According to the question, we need to draw the root locus for the given function as shown below…

Q: source entering to (2.) A 110 Vems bet the apparent the load 120 VA at a) complex power. 6.) RMS…

Q: 22// Find the current at 10 2 by using hevenin's theorem? 292 192 10v +11+ 592 VIL 1092 H 20v

Q: α (DC) for a transistor

A: BJT (bipolar junction transistor) A transistor having a three terminal made up of semiconductor…

Q: H.W. a. Find the voltage v, for the circuit in Fig. 8. b. Sketch the v₂ and i curves and phasor…

Q: H.W. (1) Find the total admittance and impedance of the parallel network of Fig. 23 10 kn Z₁ XL R6k0…

Q: Question: 15 Analog computer works on the supply of (A) Physical strength (B) Natural strength…

Q: Using mesh analysis, find the voltage and current flowing through each of the resistive elements.…

Q: Problem 5: The Spectrum of a certain signal is illustrated below. Write the equation for the…

A: In this question we need to find a signal x(t).

Q: An incandescent bulb is connected to 220-V (rms) AC source. To obtain the same brightness, the bulb…

A: We need to select correct option for given statement

Q: design a uncontrolled and controlled three phase rectifiers

Q: b) Figure 2.1 shows the circuit diagram of a simple npn BJT common emitter amplifier. Explain the…

A: Brief description: For the above given self biased common emitter amplifier circuit we need to…

Q: H.W. (2): For the circuit of Fig. 37. a. Find the total impedance Z₁ in polar form. b. Draw the…

A: As per the guidelines given to us we can only provide the solution of first three subpart in multi…

Q: A series motor has an armature resistance of 0.202 and a series field resistance of 0.30. It is…

A: Given:Series motorArmature resistance, Ra=0.2ΩSeries field resistance, Rs=0.3ΩV=240V

Q: A three-phase motor, Y connection, 380-V, 100-kW, 110- kVA, 50 Hz. Calculate the value of capacitor…

Q: a. b C. d. Given parameters: R₁ = 20 MS2 R2 = 5 ΜΩ RD = 3.3 ΚΩ Rs = 2 kΩ Rsig = 10002 RL = 1.5 kΩ…

A: We need to find out transconductance, input and output impedance and voltage gain for given circuit

Q: A 3-phase, 12 Vdc brushless DC motor with integrated sensorless is shown in the following figure.…

A: Given A DC brushless motor,we need to determine the correct statement. Please find the below…

Q: In an ac transistor amplifier, the circuit includes capacitors as well as resistors. What is the…

A: We need to explain the role of capacitor in bjt amplifier

Q: A dc series motor drives a load a 30rev/s and takes a current of 10A when the supply voltage is…

A: In this question, We need to efficiency of the DC series motor? If input current I= 10A Supply…

Q: Q1// Find I1, I2 & 13? Where Ri= 102, R2-4022 & R3-2092 V₁-10v & v2=20v R₁ ww V₁ I ww R₂ R₂ V₂ I

Q: A three-phase motor, Y connection, 380-V, 100-kW, 110 kVA, 50 Hz. Calculate the valu of capacitor…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: What are the application of load forecasting in neural network based methods

A: It is asked about the applications of load forecasting in neural network based methods.

Q: 5. Find the input impedance at 20 krad/s for the circuit shown in Figure 4. 3 mH 200 £2 m vooo 0.592…

A: Since you have posted the multiple questions so we are supposed to answer the 1st one. 5) In this…

Q: Figure 9.5 28H) L2 10. Given the delta-delta system of Figure 9.5, if the generator phase voltage is…

A: As the given system is balanced three phase system, we can do the calculations on per phase system.…

Q: What is meant by the wye connection? How many wires are necessary? When are 4 wires used?

A: Neutral point of all the phases in wye connection connected at common point There is no neutral…

Q: electrolysis, there are 2 tanks connected in series where the current that flows is 5000 A. Each…

Q: Differentiate the poles and zeros on a first degree order system and on a second degree order system

A: Order of system: The order of the system is obtained from the closed loop transfer function. The…

Q: 9 VIN O For the transistor in the circuit shown, what minimum value of lb is required to saturate…

Q: Referring to Figure 9.3, if the generator phase voltage is 400 volts and the load is balanced with…

A: A three-phase AC generator generates three-phase AC electricity by encircling the rotor with extra…

Concept explainers

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.

Question

A 1.5 KVA 50 Hz single-phase transformer has turns ratio 40/50. The primary winding is connected to 230V, 50 Hz supply. Calculate:
a. the secondary voltage on no load.
b. the maximum value of the flux.
c. the value of secondary currents on full load.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. A 100 kVA, 3300/400 V, 50 Hz single phase transformer has 110 turns on the secondary. Determine: i. The number of turns on the primary. ii. The maximum value of the flux in the core. iii. The approximate value of primary and secondary full load currents.
Question three: A single phase, 4600/460 V, 60 Hz, transformer is connected to a 60 Hz, 4600V power supply. The maximum flux density in the core is 0.85 T. If the induced voltage per turn in 10V, determine (a) The primary turns (N1) and the secondary turns (N). (b) The cross-sectional area (A) of the core.
1. In a transformer, which options are correct:A. Works on Faraday’ law and Ampere’s lawB. DC current in the primary winding will produce voltage output in the secondary windingC. Copper losses are caused by reluctance in magnetic circuitD. Frequency of input power source will not govern the voltage induced in secondary circuit.2. Voltage ratio of input voltage and output voltage in IDEAL transformer depends on:A. Leakage fluxB. Magnetization currentC. Copper loss currentD. Turns ratio3. The core of transformer must have:
The core of a three phase, 50 Hz, 11000/550 V delta/star, 300 kVA, core-type transformer operates with a flux of 0.05 Wb. Find (i) number of H.V. and L.V. turns per phase. (ii) e.m.f. per turn (iii) full load H.V. and L.V. phase-currents.
A single-phase transformer is required to step down the voltage from 1100 V to 400 V at 50 Hz. The [5]core has a cross-sectional area of 25 cm? and the maximum flux density is 5Wb/m?. Determine thenumber of turns of the primary and secondary windings.
Q8 Complete the answer : A core type transformer operates on 410 / 225 volt, 50 Hz supply. If the cross-sectional area of the core is 30 cm? and maximum flux density is 1.1 Wb/m?, then the number of turns in secondary winding will be...............
The core of a three phase, 60 Hz, 11000/750 V delta/star, 310 kVA, core-type transformer operates with a flux of 0.056 Wb. Find(i) number of H.V. and L.V. turns per phase.(ii) e.m.f. per turn(iii) full load H.V. and L.V. phase-currents
4. In a transformer, which options are correct: A. Works on Faraday’ law and Ampere's law B. DC current in the primary winding will produce voltage output in the secondary winding C. Copper losses are caused by reluctance in magnetic circuit D. Frequency of input power source will not govern the voltage induced in secondary circuit. 5. Voltage ratio of input voltage and output voltage in IDEAL transformer depends on: A. Leakage flux B. Magnetization current C. Copper loss current D. Turns ratio 6. The core of transformer must have A. Low reluctance C. High reluctance B. High resistance D. Low resistance 7. An overexcited synchronous motor behaves like: B. Resistive load D. DC generator A. Inductive load C. Capacitive load 8. The amount of real power delivered by a synchronous generator connected to an infinite bus can be controlled by adjusting A. System frequency C. Full load frequency B. No load frequency D. Terminal voltage
A 100 kVA, 3300/400 V, 50 Hz single phase transformer has 110 turns on the secondary. Determine: i.The number of turns on the primary. ii.The maximum value of the flux in the core. iii.The approximate value of primary and secondary full load currents.
3. The low-voltage winding of a 3000/200-V, 50-Hz, a single-phase transformer has 80 turns and is installed on a core with an efficient cross-sectional area of 150 cmz. Make a calculation on: a. the high-voltage winding's number of turns b. the value of the maximum flux density in the core
1. A 2.4 kVA single phase ideal transformer has 150 turns on the primary and 75 turns on the secondary winding. The primary is connected to 200 V, 50 Hz supply, find: i) The full load primary and secondary currents. ii) The primary and secondary EMF per turn. ii) The maximum magnetic flux in the core.
A single phase 60 Hz transformer has its core volume of 1.5x10-3 cu m. The maximum flux density is 1.0 tesla and the hysteresis constant of the core is 6000. find the hysteresis loss.