9.5-2 A simply supported beam (E = 12 GPa) car- Tics a uniformly distributed load q = 125 N/m, and a point load P = 200 N at mid-span. The beam has a rectangular cross section (b = 75 mm, h = 200 mm) and a length of 3.6 m. Calculate the maximum deflec- tion of the beam. %3| |C L/2 L/2 h PROBLEM 9.5-2

9.5-2 A simply supported beam (E = 12 GPa) car- Tics a uniformly distributed load q = 125 N/m, and a point load P = 200 N at mid-span. The beam has a rectangular cross section (b = 75 mm, h = 200 mm) and a length of 3.6 m. Calculate the maximum deflec- tion of the beam. %3| |C L/2 L/2 h PROBLEM 9.5-2

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.3.2P: A fixed-end b earn is subjected to a point load at mid-span. The beam has a rectangular cross...

See similar textbooks

Similar questions

A fixed-end b earn is subjected to a point load at mid-span. The beam has a rectangular cross section (assume that the h/b ratio is 2) and is made of wood (E = 11GPa). Find height h of the cross section if the maximum displacement of the beam is 2 mm. Calculate the displacement of the beam at the inflection points.
-5 Calen1ate the deflections S 3a nd
Copper beam AB has circular cross section with a radius of 0.25 in. and length L = 3 ft. The beam is subjected to a uniformly distributed load w = 3.5 lb/ft. Calculate the required load P at joint B so that the total deflection at joint B is zero. Assume that£ = 16,000 ksi.
-3 The deflection curve for a simple beam AB (see figure) is given by v=q0x360LEI(7L410L2x2+3x4) Describe the load acting on the beam.
A 356 x 171 US45 steel beam is supported at ends of a span of 5.5m. The beam carries a safe inclusive UDL of 12KN/m and a point load of 75KN at mid-span. Calculate the maximum deflection due to its load. Let: E= 205000N/mm2 I= 12070cm4 Deflection = PL^3/48EL Deflection UDL = 5wL^3/384El
The beam is subjected to the distributed loading as shown. Use E = 30,000 ksi, I = 394 in.4 , L = 23 ft, the max load distribution density at B w0 = 5 kip/ft, calculate the deflection at the middle of the beam: ___ in. Use apendix at end of the textbook and write down all the steps which lead to your anser. Pay attention to unit conversion, and calculate your answer to 1 decimal place
The Flexor loading micrometer will be used to load the beam. Calculate the deflection required to bend the beam to the desired strain. Deflection in a cantilever beam b inches wide by t inches thick is: 4PL3 y = Ebt3 %3D (4) where: y= deflection (in), P= force, lbs, L= distance from clamp to loading micrometer (10.0 in), E = Young's modulus for aluminum (10.4E6 psi). %3D %3D Stress at the rosette is given by: Mc/ = 6Px (5) %3D bt2 where: x= the distance from the loading micrometer to the rosette centerline (9.0 in), and P, b and t are as defined above. Using equations (4) and (5) above, determine the deflection required to impose a 15 Kpsi stress in the beam at the gage rosette centerline. What force will be applied by the loading micrometer at 15Kpsi? Do your work in the space below.
9.5-2 A simply supported beam (E = 12 GPa) car- THes a uniformly distributed load q point load P = 200 N at mid-span. The beam has a rectangular cross section (b = 75 mm, h = 200 mm) and a length of 3.6 m. Calculate the maximum deflec- tion of the beam. 125 N/m, and a %3D %3D A |C L/2 L/2 h PROBLEM 9.5-2
2 Find the equation of deflection (under the uniformly distributed load) and calculate the maximum deflection of the floor beam in mm. Given E=200GPA, Ix=87 x 10^6 mm^4 and ly=18.7 x 10^6 mm^4. 1.2 kN/m D -2.4 m- 0.6 m 0.6 m
For the beam shown below, compute the following: Assume El = 1 X 10³ N-m² W = 300N/m 1.5m 0.5m 2 m R1 (16-20) Compute the mid-span deflection y = = (21-25) what is the max. deflection Y max _mm R2
please translate the following problem descriptions into al diagrammatic representation, solve for/draw the shear force and bending moment diagrams and find the deflection and/or slope as indicated: 3. A 16 ft. long simply supported beam is loaded by a 1 k/ft uniform distributed load for the first 6 ft. and (2) point loads, 3 kips each, at 9 ft. and 12 ft. A Structural No. 1 timber (E = 1,600,000 psi) is specified with nominal dimensions of 6x12. Find the magnitude and location of the maximum deflection.
BP2: A simply supported beam length of 2 m is redundantly supported at l/3=0.67 m and carries a distributed load of 2.5 kN/m. The beam is made of steel and has a diameter of 25 mm. Determine deflection at x=21/3=1.33 m.