8. A 2-pole d.c shunt motor operating from a 200 V supply takes a full-load current of 35 A, the no- load current being 2 A. The field resistance is 500 2 and the armature has a resistance of 0.6 0. Calculate the efficiency of the motor on full-load. Take the brush drop as being equal to 1.5 V per brush arm. Neglect temperature rise. Rajiv Gandhi Tech. Univ Bhopal. 20001 (82.63%)

Q: For the circuit shown below, thevenin voltage at terminals a-bis 50 www 0.51, 1A 50² ba ob 10 V

A: Given circuit-     To find- Thevenin voltage.

Q: Consider the square wave shown in the picture below (with a frequency of = 1 rad/s). atos 2π Using…

A: Low pass filter A low-pass filter is a filter that enables low-frequency signals to pass through…

Q: 1. Calculate the bandwidth of an FM system (using Bessel The Table) when the maximum deviation (o)…

A:

Q: the circuit in question 1 has flow of 1.25 amperes. what is the applied voltage?  question 1: the…

A: It is given that: I=1.25 AVA=260 VAϕ=64°

Q: Calculate the RMS value of the following waveforms: (a) (b) (c) v(t) (V) 3 10 i(t) (A) v(t) (V) 4 0…

A: Given: To find: RMS value of the above signals.

Q: Vin (t) R M + Vout (t) 1 RC W = Wc = equation (5) Vin(t) = cos(wt) equation (9) Fig. 1. A simple…

A: Given data The capacitance value is C=0.047 μF The cut-off frequency of the filter is fc=340 Hz The…

Q: The total current in this circuit is _______.                     8.8 mA   7.4 mA   6.5 mA…

A: Given: In this question, the given details are, The given circuit is, To find the value of the…

Q: A single phase, 60Hz, 200-km medium nominal-T transmission line supplies a load of 700 MW at 0.95…

A:

Q: 3) Find lo and Ix using nodal analysis -j2n 10/30° V Io 402 ww j1 Ω 21₁

A: In this question We need to current Io  and Ix  using the nodal analysis as shown the circuit.  We…

Q: 2. Determine the currents 11, 12, and 13 for une network shown. Assume that the diodes are of…

A: Given that diodes are of silicon

Q: Find the value of V_R1, V_R2, V_R3, V_R4.

A: Given: In this question, the given details are, Here, the given circuit diagram is, To find the…

Q: 30 v Q2 + R₁ ww 10092 (iii) R₂ ww 6892 R3 ww 2692 R4 Total resistance RT 4792 FIGURE Q2 R5 ww 4792…

A:

Q: Q1 using the curves of Fig. 1: a. Determine the voltage across Ge diode at a current of 2 mA. b.…

A: The required diode voltage can be calculated by using the given diode characteristics graph. Based…

Q: Design a PLL as shown in Fig. 16.58(c) so that fo = 5 kHz and fe = ±50 Hz. Assume Vcc= -VEE = 15 V.

A: PLL is conmanly use IC device. Given is the circuit diagram of PLL. Given parameters are

Q: Consider a signal given by the following Fourier series 1 x(t)=1+ Σ -сos(2πh 300t) (√3) n=1 a)…

A: This question is based on exponential Fourier series of signals. It uses Parseval's power theorem.…

Q: (c) Determine the speed of the startor field.

A: It is given that: P=100 hpf=60 Hzp=6s=3%=0.03

Q: A coil having an inductance of 200 mH is magnetically coupled to another coil having an inductance…

A:

Q: Question.1 The power delay profile of a typical urban mobile radio channel is given below: 1.0 0.8…

A: Given, The power delay profile of a typical urban mobile radio channel is shown below,

Q: Which equalization filter would be best suited to remove unwanted low end 'boominess' in a track?…

A: We need to explain the equalization filter that would be best suited to remove unwanted low end…

Q: A radio broadcast antenna is located at the top of a steep tall mountain. The antenna is…

A: It is given that: P=6kWf=104.3 MHz

Q: Given the system, obtain the overall system function and the difference equation.

A: Given

Q: Q/1/ Single phase half-wave uncontrolled rectifier. The battery charger circuit that is used to…

A: Given, The supply voltage, V=250 V The supply frequency,  fs=50 Hz Limiting resistor, R=10 Ω

Q: VL = 600 ohms V2 = 500 ohms V3 = 100 ohms

A:

Q: Question #7) Given the following transmission line that is terminated with an ideal "short circuit":…

A: Given, The diagram of the transmission line,

Q: Consider the signal x()= cos(57)sin(37). a) Find the exponential Fourier series for the signal…

A: This question is based on exponential Fourier series.

Q: VI VA R I ↓ -0 Vout Broad

A: We need to find out the output impedance for given circuit and we need to draw small signal model .

Q: 6. . The phase voltage of a 3-phase voltage source is 120 V. It is supplied to a star connected load…

A:

Q: Control Systems > Controllers and Compensators Question A phase lead compensating network ha its…

A: Given- A phase lead compensating network, Transfer function- Gcs=101+0.04s1+0.01s, To Find- The…

Q: ELECTRONICS CASE/INSULATION BACKING MATERIAL PZT CRYSTAL MATCHING LAYER

A: The above-shown diagram is the ultrasonic transducer. The diagram shown is the probe of the…

Q: The figure below shows the voltage-current relationship of a resistor. The value of this resistor is…

A: Given- Voltage-current relationship:   To find- The value of resistor R.

Q: ② lim 2 60 를 In (Itaex)

A: To solve integral of given question

Q: 3. A 230 V series motor is taking 50 A. Resistance of armature and series field windings is 0.2 £2…

A:

Q: Development standards of radio frequency for human safety

A: Radio frequency-  Radio frequency is defined as the frequency at which radio signals operates and…

Q: 3 mA • 25 ΚΩ 20 ΚΩ ww 5 mA b R, = 0—50 kΩ

A:

Q: Drive from basic principles the loss coefficients (B coefficients ) for the system as shown in…

A:

Q: The A-A circuit is given below, where V₁ = 199 20° V. Vb-199 Z-120° V, and Ve=199 Z120° V. NOTE:…

A: In this question,  We need to determine the phase current of the given Delta Delta circuit.  We know…

Q: Q1 using the curves of Fig. 1: a. Determine the voltage across Ge diode at a current of 2 mA. b.…

A:

Q: The transfer function H(F) of a filter is shown below. The input signal is given by : Vin (t) = 4+3…

A: Given data The expression for the input signal is Vint=4+3cos104πt-30°+5sin24000πt The transfer…

Q: Question 4 Calculate the work done in moving 2 C charge from B(1,0,0) to A(0.3.0) along a straight…

A: given  Q=2C B(1,0,0)  A(0,3,0) E=5 ax -8x ay V/m

Q: 1. Given the BJT transistor characteristics of Fig. 1: (a) Draw a load line on the characteristics…

A: The required parameters can be calculated by using the given transfer characteristics curve and the…

Q: Consider the unity feedback system shown in Figure 2 where R(s) is reference input and Y(s) is…

A: Given: Block diagram:

Q: Write expressions for H(jw) = Vo/V₁, its magnitude |H(jw)|, and its phase ZH(jw) as a function of w…

A: Given data: The circuit are given in which resistance, inductance and the capacitances are connected…

Q: Resistive load of 84.6 MVA is connected to a bus bar with 9.4kV. If the base of 100MVA and 10kV are…

A: It is given that:- Actual bus bar voltage VAL = 9.4 KVBase MVA = 100 MVABase KV VBL =10 KV

Q: -4. A 30 KW, 250-V, d.c. shunt generator has armature and field resistances of 0.060 and 100…

A:

Q: Consequently, power supply and heat dissipation are two other constraints that must be taken into…

A: Electrical Devices and circuit- As we all know that every electrical circuit or device operates on…

Q: What is the current through R₂? VS1 15V R1 68 22 A. 3.19 A B. 319 mA C. 1.73 A D. 173 MA VA R2 30 22…

A: We need to find out the current through given resistor for given circuit .

Q: Let's assume we have 3 capacitors with each capacitor having a value of IC capacitance. What is the…

A: Given, The circuit diagram,

Q: A distributor cable in the form of a ring main ABCDEA, supplies loads of 20, 60, 30, and 40 A taken…

A: The diagrammatic representation is drawn from the given data. This question is based on distribution…

Q: Definition of setpoint, error and offset in process control system

A: To define: Set point, error and offset in process control system.

Q: State TRUE or False  Critical clearing angle depends on system configuration   Critical clearing…

A: In this question we need to check statement -1 and statement -2 is true or false

Motor Load, Torque, and Power Quality Requirement

An electric motor is a gadget that changes electrical energy into mechanical energy over to follow up on a mechanical burden. The weight set on the motor because of this mechanical movement is known as motor load. Appropriately matching the motor burden to the engine is vital to forestall harm to the engine or wasteful and unnecessary expensive activity. Engines perform such undertakings as moving a thing starting with one spot then onto the next, cutting it, changing its shape, etc. The motors might be evaluated as far as a few variables including power yield, voltage, current, and temperature. Harm to an engine might happen when it is worked under over the top engine load contrasted with its appraised limit.