75 mm 50 mm The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75mm and G = 35 GPa. For the steel segment BC, the diameter is 50mm and G = 83 GPa. Given that a = 2m and b = 1.5 m, compute the largest torque T that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. A Bronze B Steel

75 mm 50 mm The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75mm and G = 35 GPa. For the steel segment BC, the diameter is 50mm and G = 83 GPa. Given that a = 2m and b = 1.5 m, compute the largest torque T that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. A Bronze B Steel

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
Q2: The pin-connected structure shown in figure below consists of a rigid member BED and three steel rods (E= 200 GPa). Each of the rods AB and CD has a 200 mm? cross-sectional area and rod EF has a 625 mm? cross-sectional area. If a load of P= 36 kN is applied at E, determine: (a) the change in length of rod EF. (b) the stress in each rod. A 300 mm E P-36 kN 300 mm DIO 400 mm 500 mm
A solid 2.95 in. diameter shaft is subjected to a torque of T = 305 lb-ft and an axial load of P = 4700 lb. (a) Determine the principal stresses and the maximum shear stress at point Hon the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. N Answer: (a) Op1= i Op2= i A Tmax in-plane i H (1) psi psi psi T B (b) Show the stresses of part (a) and their directions on an appropriate sketch.
H B A An aluminum rod AB of diameter 2.8 inches is connected to a lever of length L = 5.6 feet. Consider that the height H = 3.4 feet, and the allowable torsional shearing stress of aluminum is 1111 psi. What is the maximum allowable force P in lbs?
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B, = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 ВЗ ... 10KN 15KN 30KN A 218.75 B 125 C 62.5 D 31.25
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel
The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate the maximum shear stress in each segment when the two torques are applied.
In the following figure, the steel plate must support maximum load of P=130 kN. The ultimate shear stress of the steel is Tu=342 MPa. Knowing that the diameter of steel bolts is d=27 mm, determine the factor of safety used for this design. (Hint: The steel plate is attached to a beam using three steel bolts) P Factor of Safety:
Q2: The pin-connected structure shown in figure below consists of a rigid member BED and three steel rods (E= 200 GPa). Each of the rods AB and CD has a 200 mm? cross-sectional area and rod EF has a 625 mm? cross-sectional area. If a load of P= 36 kN is applied at E, determine: (a) the change in length of rod EF. (b) the stress in each rod. B. 300 mm E P=36 kN 300 mm 400 mm 500 mm
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torqueT that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel
6- A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. B O T= 5 KN•m Steel core r=15mm G=78 GPa bross cylinder ro=20mm (outer diameter) G=39 GPa
A (1) B R (3) R D FIGURE P1.6/7. P1.7 (WP Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in Figure P1.6/7. One load of P = 30 kips is applied to the assembly at A, two loads of Q = 25 kips are applied at B, and two loads of R = 35 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 20 ksi. The normal stress magnitude in steel rod (2) must be limited to 35 ksi. The normal stress magnitude in brass rod (3) must be limited to 25 ksi. Determine the minimum diameter required for each of the three rods.