7. What is the response to unit step function input when all initialconditions are zero.R+2S(S + 3)a) C(t) = 1 + 2e-t +e-2tb) C(t) = 1 – 2e-t + e2tc) C(t) = 1 – et + 2e-2td) C(t) = 1 – 2e t + e-2t

Answered: Image /qna-images/answer/28864e49-cc4e-41c7-aa0b-e1e9b5f94a58.jpg

7. What is the response to unit step function input when all initial conditions are zero. S(S + 3) a) C(t) = 1 + 2e-t + e-2t b) C(t) = 1 – 2e-t + e2t c) C(t) = 1 - e-t + 2e-2t d) C(t) = 1 - 2e-t + e-2t + R.

7. What is the response to unit step function input when all initial conditions are zero. S(S + 3) a) C(t) = 1 + 2e-t + e-2t b) C(t) = 1 – 2e-t + e2t c) C(t) = 1 - e-t + 2e-2t d) C(t) = 1 - 2e-t + e-2t + R.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2- Using Matlab, what are the step response curves of the closed-loop system, as shown in fig.1. the feedback represents the second-order dynamic system. (fill in the following table) For=0.4 Wn 1 3 6 9 10 R(S) 0.1 0.3 0.6 0.9 1 For w 5 rad/sec 3 Settling time Peak response 2 Wn s(s+23wn) Settling time Peak response C(s) Discuss the follow Which parameters or w occur on the rise time of the response? Which parameter increases the speed of response? Which parameters can be decreases the response amplitude? Which parameter decreases the steady error state? fig.2
iv. G(s): = 54 s²+12s+36 a) Find the location of the poles, natural frequency and damping ratio values. b) Determine the forms and write the general expression for the unit step response. c) Find Css (steady state value) and Peak value:.... d) ******** Revise each transfer function to produce unit step response double approximately two tim slower ....................
öalg äbäi The closed-loop system transfer function of a control system is given by the following figure, for unit step input what is the * ?output 2(s – 2) R(s) (s +2)(s + 1) c(s) | %D a- -1+e-2t – e-t b- -1 – e-2t + e-t c- -1 + 4e-2t – 3e-t d- -1 – 4e-2t + 3e¬t a d
1 Problem You are given the following data (below) showing the steady-state output response, x(t), of a mass-spring-damper (stable, LTI) system to a sinusoidal input u(t) = A sin(wt). This snapshot is the response after all the transients have decayed (the time is shifted to start at zero for conve- nience). x 0.5225 Displacement pu(t) Sinusoidal force input x 0.1041 1.5 1 Y2 х 0.2783 Y1.372 0.5 h ok -0.5- -1 -1.5 x(t) M Assume: bl u(t) x(t) Horizontal Plane (no gravity) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Time (sec) www k Using only the data provided above (the blue line is the input u(t) and the red line is the output x(t)), determine: 1. The frequency of the input in rad/s 2. The amplitude of the input, A 3. The frequency of the output in rad/s 4. The output-input ratio |G(iw)| = max(x(t)) max(u(t))' at the particular input frequency shown. 5. The phase (also called phase lag) of the output, $, at the particular input frequency shown in degrees. Note the phase is generally…
1) Determine the steady-state (forced) response and the time constant (or dominant time constant) for each of these systems: a. x+ 2x = 0 with x(0) = 10 b. 4x + 8x + 40x = 20 with x(0) = 0 and x(0) = 0 10x + 4x = 24 with x(0) = 0 C. d. *+ 34x + 64x = 8 with x(0) = 0 and x(0) = 0
H.w 2: The open loop response, that is, the speed of the motor to a voltage input of 20V, assuming a system without damping is dw 20 = (0.02) + (0.06)w. dt If the initial speed is zero (w(0) = 0) ,and using the Runge-Kutta 4th order method, what is the speed at t = 0.8s? Assume a step size of h = 0.4s.
v. G(s): = 24 (s+20) (s+4)² (s+24) a) Find the location of the poles, natural frequency and damping ratio values.. b) Determine the forms and write the general expression for the unit step response.. c) Find Css (steady state value) and Peak value.............. d) Revise each transfer function to produce unit step response double approximately two tim slower ..............................................................................................................................….........
Problem-3. Consider the closed loop transfer function from R(s) to C(s) as given below as given below. 85 H(s) = (s+5)(s? + 2s +17) MATLAB gives the partial fraction values of the Laplace transform C(s) to the unit step input as follows: Num: Denom: -0.5313 -5.0000 -0.2344 + 0.3906i -1.0000 + 4.0000i -0.2344 - 0.3906i -1.0000 - 4.0000i 1.0000 d) Find the overshoot and peak time by using the reduced-order transfer function Hint:Tp = e-(n{//1-§2 %OV = Wn V1- 2)
QUESTION 2 Consider a system model given by d²x (t) d1² 2- + 3x (t) = 48 (t) x (0) = 1 dx (t) dt =0- = -3. What is the initial response at t=0+? x(0+)=0 and dx/dt(0+)= -1 x(0+)=1 and dx/dt(0+)= 4 x(0+)=1 and dx/dt(0+)= -1 x(0+)=2 and dx/dt(0+)= -1 x(0+)=1 and dx/dt(0+)= 1 x(0+)=4 and dx/dt(0+)= 1
Q.4- A model for feedback control system employing both angular position and velocity feedback is shown in figure bellow .The equation describing d²0 do di the system is J di² - = • K.[V₁-K₁0. K₂0-Ka ((1) Summing V,(r) Motor 白口食 amplifier Velocity sensor K₂8 Position sensor Where J is the rotary inertia KandK are the position and velocity feedback gains, and K, is the gain between the input voltages to the motor torque produced. Derive expression for the closed loop system undamped natural frequency and damping ratio.
Graph/Plot the output step response from t=0 to t=10 with a 0.1-second interval.
Match the transfer function with correct Bode phase plots. G(s) = 5 $+7 G(s)=s+5 G(s) = s+10 S S G(s) = S+ 10 QUESTION 10 90 deg 00 0 deg -90 deg 180 deg B. D 90 deg @ 0 deg -90 deg 180 deg 90 deg @ 0 deg -90 deg 180 deg 90 deg @ 0 deg -90 deg 180 deg