6a. A vertical force of 80 lb acts on a crankshaft that is held in place by a bearing at A that supports radial forces only and a bearing at B that supports radial and axial thrust forces. Determine the horizontal force, P applied at the handle to keep it in equilibrium (not moving) and the components of force at bearings A and B. (Hint: the bearings do not support couples) 80 lb 10 in. 14 in. 14 in. 6 in. 8 in. in.

6a. A vertical force of 80 lb acts on a crankshaft that is held in place by a bearing at A that supports radial forces only and a bearing at B that supports radial and axial thrust forces. Determine the horizontal force, P applied at the handle to keep it in equilibrium (not moving) and the components of force at bearings A and B. (Hint: the bearings do not support couples) 80 lb 10 in. 14 in. 14 in. 6 in. 8 in. in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The frame shown in the figure is supported by a hinge at A and a roller at E. Compute the horizontal and vertical components of the hinge forces at B and Cas they act upon member AC. (Positive Upward and to the Right) 240 lb D 3'
Q2/ Determine the resultant moment of the force about point C F =400N 100 N D 30° 45 0.3m 100 N -0.4m- tozm t B.
F4–30. Replace the loading system by an equivalent resultant force and couple moment acting at point O. Z. F1 = 100 N М. 3 75 N-m C 0.3 m F, = 200 N 0.5 m 0.4 m y
6 kN/m 3 kN/m A В 4.5 m 1.5 m Q1- The beam shown is subjected to two types of distributed loading. Support A is a pin, support B is a roller. Determine the following: (a) The Total load is carried by the beam is . kN (b) Vertical Force Reaction at support B, By is kN (c) Vertical Force Reaction at support A, Ay is kN
2 ft -2 ft 2 ft A 90 65 200 lb 100 lb 2. A beam AB is loaded as shown. The beam is pin-connected to the wall at A. At Ba 10-inch diameter pulley is attached through frictionless bearing to the beam. A rope passes around the pulley and is connected to C and D vertically above the extremities of the horizontal diameter of the pulley. Determine the pin reaction at A and the tension in the rope. Hint: Pin connection has vertical and hozirontal reactions.
A rectangular column with cross-sectional dimen- sions b and h is pin-supported at ends A and C (see figure). At midheight, the column is restrained in the plane of the figure but is free to deflect perpendicular to the plane of the figure. Determine the ratio h/b such that the critical load is the same for buckling in the two principal planes of the column. CO L Ix 2 B Soati
Prob 4. The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter of 0.75 in. If a force of 10 kip is applied to the bar, determine the angle of tilt of the bar. 2 ft B -1.25 ft- E D 0.75 ft F 10 kip 3 ft 1 ft
A 72 2 (a) 8 W+ W 2 (c) 2 2W+ с W) 2 T 72 30⁰ A beam AB of length 1 and weight w supports a load W at its free end B and is hinged at its end A. A wire CD supports the beam at the mid point C making an angle of 30° with the horizontal. What is the value of tension T in the wire CD? D B W (b) 4 (2W + w) (d) 4 W+ W 2
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. Determine (a) the maximum shear stress in the shaft; and (b) the angle of twist of end D relative to end A. Use G = 12 x 10° psi for steel, and assume that friction at bearing D is negligible. A 4 in. 3.5 in. 3.5 in. D B C 6 ft t4 ft 2 ft -
Q2/ Determine the resultant moment of the force about point C F=400N 100 N D 30 45 0.3 m A 100 N -04m tozm t 0.2 m
The 20-mm-diameter A-36 steel rod is subjected to the axial forces shown. Determine the displacement of end C with respect to the fixed support at A. 600 mm 400 mm 50 kN 40 kN B 50 kN
The 6.9-lb force is applied at point A of the crank assembly. Determine the moment of this force about point O. 2.55" A 37° F = 6.9 lb 0.80" -y