•60 Models of torpedoes are sometimes tested in a horizontal pipe of flowing water, much as a wind tunnel is used to test model airplanes. Consider a circular pipe of internal diameter 25.0 cm and a torpedo model aligned along the long axis of the pipe. The model has a 5.00 cm diameter and is to be tested with water flowing past it at 2.50 m/s. (a) With what speed must the water flow in the part of the pipe that is unconstricted by the model? (b) What will the pressure difference be between the constricted and unconstricted parts of the pipe?

•60 Models of torpedoes are sometimes tested in a horizontal pipe of flowing water, much as a wind tunnel is used to test model airplanes. Consider a circular pipe of internal diameter 25.0 cm and a torpedo model aligned along the long axis of the pipe. The model has a 5.00 cm diameter and is to be tested with water flowing past it at 2.50 m/s. (a) With what speed must the water flow in the part of the pipe that is unconstricted by the model? (b) What will the pressure difference be between the constricted and unconstricted parts of the pipe?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An airplane wing, with chord length of 1.5 m and span of 9 m, is designed to move through standard air (v= 1.51x105 m²/s) at a speed of 7.5 m/s. A 1/10-scale model of this wing is to be tested in a water tunnel (v= 1.00×106 m²/s). If viscous effects govern, what speed is necessary in the water tunnel to achieve dynamic similarity? a.11.33 m/s b.4.97 m/s c.1.51 m/s d.2.98 m/s
A model of the Airbus 320 is tested in a wind tunnel using air at standard conditions. If the tunnel airspeed is 50m/s, calculate the water speed if the same model is to be tested in a water tunnel atdynamically similar conditions. Take mair=1.73 x 10-5Pa.s, mwater=10-3Pa.s, rair=1.225kg/m3 andrwater=1000 kg/m3.
A small, axisymmetric, low-speed wind tunnel is built to calibrate hot wires. The diameter of the test section is 6.68 in, and its length is 12.5 in. The air is at 60°F. At a uniform air speed of 5.0 ft/s at the test section inlet, by how much will the centerline air speed accelerate by the end of the test section? What should the engineers do to eliminate this acceleration?
In the field of air pollution control, one often needs to sample the quality of a moving airstream. In such measurements a sampling probe is aligned with the flow as sketched in Fig. A suction pump draws air through the probe at volume flow rate V· as sketched. For accurate sampling, the air speed through the probe should be the same as that of the airstream (isokinetic sampling). However, if the applied suction is too large, as sketched in Fig, the air speed through the probe is greater than that of the airstream (super iso kinetic sampling). For simplicity consider a two-dimensional case in which the sampling probe height is h = 4.58 mm and its width is W = 39.5 mm. The values of the stream function corresponding to the lower and upper dividing streamlines are ?l = 0.093 m2/s and ?u = 0.150 m2/s, respectively. Calculate the volume flow rate through the probe (in units of m3/s) and the average speed of the air sucked through the probe.
A 1:7 scale model simulates the operation of alarge turbine that is to generate 200 kW with a flowrate of 1.5 m3/s.What flow rate should be used inthe model, and what power output is expected?(a) Water at the same temperature is used in bothmodel and prototype.(b) The model water is at 25°C and the prototypewater is at 10°C.
(a) A model low speed centrifugal compressor (a “blower") runs at 430 rpm and delivers 10 m/s of air against a pressure head of 60 mm of water. If the pump efficiency is estimated to be 80%, how much power is required to drive the compressor? (b) A geometrically similar compressor is made with a diameter 1.8 times the size of the model and is required to work against a pressure head of 80 mm of water. Determine the operating speed and the power needed to drive the compressor assuming dynamically similar condi- tions apply.
Pipelines are cleaned by pushing through them a closefitting cylinder called a pig . The name comes from thesquealing noise it makes sliding along. Reference 50describes a new nontoxic pig, driven by compressed air, forcleaning cosmetic and beverage pipes. Suppose the pigdiameter is 5-15/16 in and its length 26 in. It cleans a6-in-diameter pipe at a speed of 1.2 m/s. If the clearance isfi lled with glycerin at 20 8 C, what pressure difference, inpascals, is needed to drive the pig? Assume a linear velocityprofi le in the oil and neglect air drag.
A centrifugal pump, pumps water at 0.240 m3/s rotating at 1200 rpm, a prototype pump using 10 lit/s is to be tested. If the diameter of the model is 3 times the diameter of the prototype, at what speed should the prototype run, if the pump pumps oil at a head of 30 meters. (a)What would be the required horsepower to drive the model at an efficiency of 0.8? (b)What would be the required horsepower to drive the prototype?
Find the air horsepower of an industrial fan that delivers 40m3/s of air through a 700mm x 1000mm duct if static pressure is 150mm of water gage and air density is 1.18kg/m3 Answer: 182.2
PROPAGATION OF ERROR You are tasked to supervise the design of 0.5MW wind turbine to be constructed in a Wind Farm in Pililla, Rizal. Suppose the design criteria are as follows: The air density as surveyed after 2 year period averaged at 1.225 kg / cubic meter. The sweeping diameter of the rotor blades is 125m, and the anemometer reading in the area amounts to 4.2m/s on a 2 year period of survey. if the diameter measurement is off by 0.1m and the anemometer reading is also fluctuating by 0.05m/s. In the design specifications given, if the actual measurement of power via the substation amounts to exactly 530kW and given that the windspeed is off by 0.05m/s, what could have been the error in the measurement of diameter? Your answer must be in 3 decimal places and in correct signs and measurement. Show complete solution in paper.
As we learned, Bernoulli's equation is not to be used in many situations. Let's say you are examining changes between two points in a flow. Which ONE of these scenarios could you appropriately use Bernoulli's equation on? O A turbine is situated between the two points There are large changes in kinetic energy between the two points The mass flow rate between the two points changes with time There are large changes in density between the two points There are large viscous losses between the two points QUESTION 10 A 12 cm diameter jet of air strikes a plate positioned normal to the flow, with all air deflected away parallel to the plate. If the air flows at a speed of 20 m/s, what is the force needed to held the plate in place? Do not use a linear momentum correction factor. O 0.272 N 10.9 N 4510 N 5.45 N 0.340 N
C1 (a) A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area of 2.2 N/m2 to maintain this speed with using an oil of specific gravity 0.75. Find the dynamic viscosity and kinematic viscosity of the fluid between the plates. C1 (b) Calculate the specific weight, density, and the specific gravity of a liquid having a volume of 665000 cm3 and weight of 72 kN find : C1 (a) 1_The dynamic viscosity of the fluid (in Centipoise) 2_The kinematic viscosity of the fluid (in stokes) C1 (b) 3_Specific Weight in (N/m3) 4_Density of liquid (in kg/m3) 5_Specific gravity of liquid