6.41.1 The voltage across an inductor with 2 H capacitance is 12. (1 – e-dr) v, where a = 1.2. If the initial current through the inductor is 0.3 A, determine the current (in A) through this inductor when t= 1.0 s. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Your Answer: Answer

6.41.1 The voltage across an inductor with 2 H capacitance is 12. (1 – e-dr) v, where a = 1.2. If the initial current through the inductor is 0.3 A, determine the current (in A) through this inductor when t= 1.0 s. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Your Answer: Answer

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 5PP: Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 -...

See similar textbooks

Similar questions

Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
a. Show how you would connect all five capacitors to get a maximum capacitance and find the maximum capacitance in terms of C. b. Show how you would connect all five capacitors to get a minimum capacitance and find the minimum capacitance in terms of C.
Please draw the problem and answer, thank you. A capacitor is made of 2 rectangular metal plates with side length of 3 cm x 6 cm separated by a distance of 2.36 cm with water in between the plates. The capacitor has a voltage of 110 v and is not connected to a battery. Calculate the capacitance. What is the new capacitance if we replace water with a new dielectric material with a constant of 3.75 in between the plates? What is the new voltage? What is the charge on each plate?
When the capacitor is charged current flows on either side of the capacitor. Do electrons cross the gap to allow the current on the other side of the circuit?(b) Is charging and discharging time of capacitor equal in a theoretical RC circuit?Plase explain your answer by using relating formula.
Energy stored in capacitor. Answer it in 30 mins. Draw/sketc the problem thank you. Write the basic equation before the soln. Thank you
What is the characteristic equation for the inductor current in the following circuit?
Two capacitors A and B having capacitance of 20uF and 30uF respectively are connected in series to a 600v supply. Determine the p.d across each other. If a third capacitor C is connected in parallel with A and it is found that p.d across B is 400v, calculate the capacitance of C and energy stored in it
An inductor is "charged" to some value, then connected in series with a 1002 resistor and allowed to "discharge". A measurement of the potential difference across the resistor is shown in the figure below. Compute the time constant of the circuit, the inductance of the inductor, and the initial current through the inductor. 12 10 8 6 Potential across resistor (V) 2 0 0 0.0001 0.0002 0.0003 0.0004 0.0005 0.0006 0.0007 time (s)
1) First part of the question: Two identical capacitors are connected in parallel and charged with a 20-V power supply as shown in the figure on the left. After the charges on the capacitors have reached their final values, the charge on each capacitor is 10 µC. Then the power supply is disconnected and a dielectric with K = 4 is inserted to fill the space between the plates of one of the capacitors. a) Find now the charge on the capacitor with dielectric. Give your answer in microcoulombs. Qo = 10 µC Qo = 10 µC| Q2 =? ► V = 20 V Battery
You are modifying the design of an existing inductor and want the inductance to be 1/2 of it's current value. You could achieve this by which of the following options. Select all that apply. Question 1 options: Decreasing the number of windings by a factor of 2. Decreasing the length of the inductor by a factor of 2. Increasing the area of the inductor by a factor of 2. Increasing the number of windings by a factor of 2. None of the other responses are correct.
A 10-9.F capacitor (1 nanofarad) is charged to 50 V and then disconnected. One can model the charge leakage of the capacitor with a RC circuit with no voltage source and the resistance of the air between the capacitor plates. On a cold dry day, the resistance of the air gap is 3× 1018 2, on a humid day, the resistance is 6 × 10° 2. How long will it take the capacitor voltage to dissipate to half its original value on each day? ... On the dry day, it will take seconds.
A capacitor is made of 2 rectangular metal plates with side length of 3cmx6cm separated by a distance of 2.36 with water in between the plates. The capacitor has a voltage of 110v and is not connected to a battery. Calculate the capacitance. What is the new capacitance if we replace water with a new dielectric material with a constant of 3.75 in between the plates? What is the new voltage? What is the charge on each plate?