6. Details of a retaining wall are shown in the figure below. The unit weight of the wall material is 23 kN/m³. Assume a reduction factor K = 2/3 to consider the cohesion and friction angle at the base slab. Check the stability of the wall in terms of overturning and sliding failure. Use Rankine's theory to compute the active earth pressure. 6.5 m tu 1 2 m Yc = 23 kN/m³ 4 m -1.5m - Soil 2 Y2 = 17 kN/m³ ₂ = 10 kN/m² P2 = 25° a = 15⁰ Soil 1 Y₁ = 16 kN/m³ c₁ = 0 kN/m² 4₁ = 30°

6. Details of a retaining wall are shown in the figure below. The unit weight of the wall material is 23 kN/m³. Assume a reduction factor K = 2/3 to consider the cohesion and friction angle at the base slab. Check the stability of the wall in terms of overturning and sliding failure. Use Rankine's theory to compute the active earth pressure. 6.5 m tu 1 2 m Yc = 23 kN/m³ 4 m -1.5m - Soil 2 Y2 = 17 kN/m³ ₂ = 10 kN/m² P2 = 25° a = 15⁰ Soil 1 Y₁ = 16 kN/m³ c₁ = 0 kN/m² 4₁ = 30°

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter14: Lateral Earth Pressure: Curved Failure Surface

Section: Chapter Questions

Problem 14.7P

See similar textbooks

Similar questions

A 6m retaining wall is supporting a soil with the following properties:Unit weight = 16 KN/cu.mAngle of internal friction = 25ºCohesion = 14 Kpaa. Assuming no tensile cracks occurs in the soil; determine its normal pressure acting at the back of the wall.b. If tensile crack occurs in the soil, calculate its active pressure acting on the wall.c. Find the location of tensile crack measured from the surface of horizontal backfill.
3. Compute the resultant lateral force for the soil-wall system shown in Figure 3. You may ignore tensile cracks. Use • A- Coloumb • B - Rankine 0=30°, y=20kN/m³ 4m Ground water table 7m c=50KN/m², p=10°, y=18KN/m³ 0=25°, y=20KN/m³ 8 m Gravity wall Figure 3
The following figure shows a section of an anchored retaining wall embedded into a saturated stiff clay layer. The sand has a unit weight of = 18 kN/m³, c' = 0 kPa and o' = 34º. The clay has a unit weight of = 20 kN/m³, c₁ = 80 kPa and = 0°. A uniform pressure of 40 kPa is applied on the soil surface. The short term stability of the wall is considered in an undrained analysis. Use the Rankin's theory of lateral earth pressure to determine the active and passive horizontal stresses. You should apply the requirements of AS 4678 and the partial factors of safety method in estimation of soil pressures. Assume the soil is in-situ and use a structural classification factor of ₁ = 1. 3m 1m Water table 1.5m 40 kPa Not to Scale Sand Clay Ta
Considering that the horizontal thrust from the back of a 5.5 m wide brick wall to the 1 m deep part of the wall is H = 55 kN a) Find the greatest stress in the base when b = 2 m.b) Find the width b so that there is a shrinkage zone at the base.(Note: unit weight of brick wall ỿ = 24 kN / m3 ) Answer: ϭmax=0,30 Mpa, b=2,23 m
A frictionless retaining wall is shown ih the figure below. q= 10 kN/m 1= 15 kN/m o = 26° d'=8 kN/m 4 m
Q3) A retaining structure is given in figure. Calculate the factor of safety against sliding. (Ignore tensile crack behavior inside active part and ground water condition. Take 1.0 m interval step for point load calculation. k₁= k₂= 0.9). 3.B m 2.C m Yn: 20.0 kN/m² D: 2Eº c: 30 kN/m² 0.5 m 0.5 m 1 3.0 m 5.0 m Y cone ➜ 5A0 KN Yn: 18.5 kN/m³ c: 18 kN/m² $: ID º 24.0 kN/m³
Determine the lateral earth pressure force on the wall (6.0 m height shown in the figure. Draw the stress distribution and locate the location of the resultant force. Sandy soil kN Ye = 20 O = 36.0°
A concrete retaining wall 8 m high is supporting a horizontal backfill having a dry unit weight of 16.25kN/m3. The cohesionless soil has an angle of internal friction of 33 degrees and a void ratio 0f 0.65. (Use four decimal places) A. Compute the rankine active force on the wall. B. Compute the rankine active force on the wall if water logging occurs at a depth of 3.5 from the ground surface. C. Compute the location of the resultant active force from the bottom.
13.22 Consider the retaining wall shown in Figure 13.38. The height of the wall is 9.75m. and the unit weight of the sand backfill is 18.7kN/m3. Using Coulomb's equation, calculate the active force, Pa, on the wall for the following values of the angle of wall friction. Also, comment on the direction and location of the resultant.
A 6m high retaining wall is to support a soil with a unit weight of 17.4 kN/m^3 , soil friction angle of 26 degrees and cohesion of 14.36 kN/m^2. Determine the Rankine active force per unit length of wall before the tensile crack. Determine the Rankine active force per unit length of wall after the tensile crack occurs. Determine the location of the acitve force after the tensile crack occurs.
A retaining wall 6 m high with a vertical back face has c'- ϕ' soil for backfill. For the backfill, γ = 18.1 kN/m^3, c' = 29 kN/m^2, and ϕ' = 18˚. Taking the existence of the tensile crack into consideration, a. determine the active force, Pa, per unit length of the wall for Rankine’s active state. b. determine the passive force, Pp, per unit length for Rankine's passive state.
1- Figure below shows a retaining wall. Determine the magnitude of the lateral earth force per unit length for the following conditions: 1) At-rest force 2) Active force Also, find the location of the resultant, 7, measured from the bottom of the wall. H (ft) y (lb/ft') 15 19 120 Sand Unit weight = y (or density = p) %3D H c' = 0 8' (angle of wall friction) = 0