5-126* A short standard-weight steel pipe (see Appendix B) is used to support an axial compressive load of 100 kN. If yield- ing (o, = 250 MPa) should not occur and the factor of safety is to be 1.6, determine the smallest nominal diameter pipe that may be used to support the load.

5-126* A short standard-weight steel pipe (see Appendix B) is used to support an axial compressive load of 100 kN. If yield- ing (o, = 250 MPa) should not occur and the factor of safety is to be 1.6, determine the smallest nominal diameter pipe that may be used to support the load.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.10.2P: A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN...

See similar textbooks

Related questions

Q: Determine the pressure difference between point A and B using the following Specific Gravity: Benzen...

A: Answer: The pressure difference between point A and B: ( PB - PA ) = 21.9078 kPa.

Q: The cantilever beam carries a uniformly varying load as shown. In addition, a 1000 lb-upward vertica...

Q: Determine the head developed by a multi-stage pump delivering 50 L/s when running at 1450 rpm if the...

Q: As an oil well is drilled, each new section of drill pipe supports its own weight and that of the pi...

Q: The level of mercury in the right limb is 0.6m above that in the left limb and the space above mercu...

Q: Determine the gauge pressure at P in the figure below which shows a compound manometer. Take all dim...

A: It is required to determine gauge pressure P

Q: A vertical square surface as shown in the figure as shown in the figure has its upper edge horizonta...

Q: Oil (S=0.87) 10 cm Water 9 сm 7 cm Mercury 40 Fig. P2.41 2.42 The pressure in pipe B in the previous...

A: Given arrangement of fluids :

Q: The sugar content of the syrup in canned peaches is normally distributed, and the variance is though...

Q: (B - Odd) The velocity of a particle which moves along the x axis is given by v = 2 – 4t + 5 t2, whe...

A: Given, Velocity of particle as a function of time = v(t) = 2 - 4 t + 5 t32 ft/s Initial position = ...

Q: What is the resulting modulus of In (2 +3 j)?

A: GivenZ=ln2+3i

Q: In the hanger shown, the upper portion of link ABC is 3/8 in. thick, and the lower portions are each...

Q: Is the adiabatic expansion of superheated steam from 850°C and 2.0 MPa to 650°C and 1.2 MPa possible...

Q: A 2024-T4 aluminum tube with an outside diameter of 3.8 in. will be used to support a 36-kip load. I...

Q: A container shown is at 90 deg F, The pressure at point A was measured at 41 in of Hg. Find the pres...

Q: motor required?

A: To find power required

Q: A U-tube is made up of two capillaries with bores of 0.0039 ft and 0.0078 ft. A liquid with a surfac...

A: Answer: The density of the liquid is 943.2875 kg/m3.

Q: 12 kg/s of steam expands in an adiabatic turbine from at 10 MPa and 450°C to 10 KPa. The inlet and e...

Q: A pump delivers 500gpm of water against a total head of 200 ft and operating at 2000rpm. Changes hav...

A: Initial conditions:Flow rate, Q1=500 gpmTotal head, H1=200 ftSpeed of pump, N1=2000 rpmChanges in he...

Q: Kerosene, SG=0.82 Air, SG=0.0012 Benzene, SG= 0.88 100mm B 200mm 150mm 90mm Water Hg 400mm

A: Given Data: The specific gravity of mercury, SG=13.6

Q: of degrees of freedom

A: To find DOF (F)

Q: Directions: Find the volume of each figure. Round to the nearest hundredth when necess 1. 2. 9 m 7 m...

A: Volume = Base Area X Height Using irregular area formula methods

Q: Determine the number of degrees of freedom of the mechanism shown in the figure below. 2, 3 1

A: Answer: The degree of freedom of the given mechanism is one (1).

Q: A pump receives 8kg/s of water at 230kPa and discharges it at 1200 kPa. Compute the power required i...

A: It is required to choose correct answer

Q: A pump driven by an electrical motor moves 20gpm of water from reservoir A to B, lifting the water t...

A: Given that: Volume flow rate = 20 gpm = 20 gal/min Total head = 255 ft efficiency of pump = 64% = 0...

Q: EX1- It is required to pump water out of deep well under a total head of 90 m. A number of identical...

A: Total head, H= 90 m Design speed, N= 1000 rpm Specific speed, NS= 30 Rated capacity, Q= 0.15 m3/s ...

Q: A sliding gate of height 1.4m and width 2.8m lies in vertical plane that weighs 25kN. When the gate ...

Q: 10. Calculate the smallest glass tube that can be used to monitor water level with a capillary rise ...

Q: 1- A well-insulated rigid tank contains 2 kg of a saturated liquid-vapor mixture of water at 100 kPa...

A: Answer: The entropy change of the steam during this process is 8.1 kJ/K.

Q: Oil ( μ = 0.478 Pa.s and ν = 5.3 *10-4 m2/s ) flows downward in a pipe which is ( 3 cm ) in diameter...

Q: The manufacturing of pie filling involves blending of concentrated product with liquid sugar and hea...

A: The amount of moisture in the steam is measured by its quality. In a mixture of steam and water drop...

Q: The biceps brachii, a muscle in the arm, connects the radius, a bone in the forearm, to the scapula ...

A: Given DataFE=6.5NW=15.3N

Q: Problem 3. The system of two blocks, cable, and frictionless pulley is initially at rest. Determine ...

Q: The left limb of a U-tube mercury manometer is connected to a water pipe line, with the mercury leve...

Q: A 40 kg block is resting on an inclined plane making an angle of 20° from the horizontal. If the coe...

A: GIVEN DATA- MASS OF BLOCK m=40kg FRCITION COEFFICIENT =0.60 WE HAVE TO FIND FORCE APPLIED

Q: rom rest. What is the speed of the ball of mass

A: To find Speed of ball m2

Q: A spherical balloon with a diameter of 4.25 m is filled with oxygen at 25°C and 16 kPag. Determine t...

A: GIVEN DATA- T=25'C Pgauge=16KPa Patm=0.99bar WE HAVE TO FIND MASS

Q: A 2-meter concrete column (Ec=30 GPa) is reinforced with six 25-mm diameter steel bars (Es=200 GPa) ...

Q: Problem 4. Determine the smallest force P that must be applied to the 150-lb uniform crate to cause ...

Q: 0.2 m 0.2 m *1-8. 0.4 m 0.6 m The floor crane is used to lift a 600-kg concrete pipe. Determine the ...

Q: Two forces of 800 N and 300 N are acting on a hook and passing through point O as shown in Figure 1....

Q: shown. Determine the resultant internal loadings acting on the section through point A. 0. 0.1 m 45

Q: 2. A fluid (s=0.95) flows through a 77 mm diameter pipe at a velocity of 6 m/sec. Compute the mass f...

A: Given data: SG=0.95d=77 mmv=6 m/s Need to determine the mass flow rate of the fluid.

Q: 4. A sliding gate of height 1.4m and width 2.8 lies in vertical plane that weighs 25kN. Determine th...

Q: 2. A helical valve spring is to be designed for an operating load range of approximately 90 to 135 N...

Q: straight line yield measured values of the velocity v for various position coordinates s. A smooth c...

Q: 4. Analyse why is it more efficient for the work cells to prepare "modules" and deliver them to the ...

A: Process strategies: These are the strategies which help in transforming the raw materials into fina...

Q: A container shown is at 90 deg F, The pressure at point A was measured at 41 in of Hg. Find the pres...

A: Given Pressure at point A=PA=41 in Hg=4112 ft in Hg

Q: Water is pumped from the upper reservoir to the lower reservoir through the piping system shown. Det...

A: Mass flow rate of water, m˙=60 kg/sh1=10 mh2=3 mL1=50 mL2=300 mL3=2 mD1=0.2 mD2=0.5 mD3=0.03 mViscos...

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

100%

5-126* A short standard-weight steel pipe (see Appendix B) is
used to support an axial compressive load of 100 kN. If yield-
ing (o, = 250 MPa) should not occur and the factor of safety
is to be 1.6, determine the smallest nominal diameter pipe that
may be used to support the load.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A standpipe in a water-supply system (see figure) is 12 ft in diameter and 6 in. thick. Two horizontal pipes carry water out of the standpipe; each is 2 ft in diameter and 1 in. thick. When the system is shut down and water fills the pipes but is not moving, the hoop stress at the bottom of the standpipe is 130 psi, (a) What is the height h of the water in the standpipe? (b) If the bottoms of the pipes are at the same elevation as the bottom of the stand pipe. what is the hoop stress in the pipes?
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
A scuba t a n k (see fig ure) i s bci ng d e signed fo r an internal pressure of 2640 psi with a factor of safety of 2,0 with respect to yielding. The yield stress of the steel is 65,000 psi in tension and 32,000 psi in shear, (a) If the diameter of the tank is 7,0 in., what is the minimum required wall thickness? (b) If the wall thickness is 0.25 in., what is the maximum acceptable internal pressure?
The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.