4.The threaded collar is used toconnect two shafts, both with right-hand threads on their ends. Theshafts are under a tension T = 8 kN.TIf the threads have a mean diameterof 16 mm and a lead of 4 mm,calculate the torque M required toturn the collar in either direction withMthe shafts prevented from turning.The coefficient of friction is 0.24.

Given Data The mean dimeter of the threads is: d=16 mm The lead is: L=4 mm Tension is: T=8 kN=8000…

4. The threaded collar is used to connect two shafts, both with right- hand threads on their ends. The shafts are under a tension T = 8 kN . If the threads have a mean diameter T. of 16 mm and a lead of 4 mm, calculate the torque M required to turn the collar in either direction with the shafts prevented from turning. The coefficient of friction is 0.24.

4. The threaded collar is used to connect two shafts, both with right- hand threads on their ends. The shafts are under a tension T = 8 kN . If the threads have a mean diameter T. of 16 mm and a lead of 4 mm, calculate the torque M required to turn the collar in either direction with the shafts prevented from turning. The coefficient of friction is 0.24.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

a. A four-cylinder engine has a 85 mm bore ? and 90 mm stroke ?, and operates at 5000 rpm.What is the power lost to piston skirt friction? b. What is the power (?) lost to main crankshaft friction in a four-cylinder engine with a 100mmbore and stroke if the engine is operating at 1500 rpm? Assume the main crankshafthas five bearings, each with a diameter of 50 mm and length of 25 mm. in hand written
A single threaded trapezoidal metric thread has a pitch of 4 mmand a mean diameter of 18 mm. It is used as a translation screwin conjunction with a collar having an outside diameter of 37mmand an inside diameter of 27 mm. The load is 400 kg and coefficientof friction is 0.3 for both threads and collar. Find:a. The collar torqueb. The required torque for threadc. The total torque
3 The press shown below has a rated load of 25 kN The twin screws have Acme threads, a diameter of 56 mm, and a pitch of 5.5 mm. Coefficients of friction are 0.05 for the threads and 0.08 for the collar bearings. Collar diameters are 88 mm. The gears have an efficiency of 95 percent and a speed ratio of 60: 1. The full-load motor speed is 1750 rev/min. a. When the motor is turned on, how fast will the press head move? b. What should be the horsepower rating of the motor? Bearings Motor Spur gears Bronze bushings (مزدوج) Foot Worm Collar bearing
thick lnange be! The total torque required to turn the double threaded power screw is 55 N.m. If the screw turns at 285 rpm and the pitch of 4mm, find: A. The horsepower input of the power screw. B. The efficiency if the weight loaded is 10 kN.
In a thrust bearing, the external and the intermal diameters of the contacting surfaces are 320 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m?. The shaft rotates atę Op rpm. Taking the coefficient of friction as 0.os, calculate the power lost in overcoming the friction. Also, find the number of collars required for the bearing.
A single square-thread screw has an input power of 3 kW at a speed of 1 rev/s. The screw has a diameter of 40 mm and a pitch of 8 mm. The frictional coefficients are 0.16 for the threads and 0.09 for the collar, with a collar friction diameter of 50 mm. Find the axial resisting load Fand the combined efficiency of the screw and collar if the screw is raising the load. The axial resisting load Fis |kN. The combined efficiency of the screw and collar is %.
34 in 3. The following data apply to the C-clamp: a. The screw is ACME with ¾" Diameter b. Coefficient of thread friction = 0.12 c. Coefficient of collar friction = 0.23 d. Mean collar radius = 0.55 in. e. Max. clamping force = 1000 lb Determine: The tightening torque The operator force at the end of the handle (Note: Use table 8-3 to determine the screw pitch (p))
A cone clutch has cone elements at an angle of 12o. The clutch transmit 25 HP at a speed of 1200 rpm. The mean diameter of the conical friction section is 16 in and the coefficient of friction is 0.35. Find the axial force needed to engage the clutch.
The effective pressure on a 400 mm diameter piston is 1.1 MN/m² when the crank is 32° beyond top dead centre. The stroke of the engine is 900 mm, the connecting rod is 1500 mm in length and the coefficient of friction for the lubricated crosshead guide is 0.025. Calculate EACH of the following: (a) the magnitude of the instantaneous torque; (b) the magnitude of the instantaneous force to overcome guide friction.
In a thrust bearing, the external and the internal diamaters of the contacting surfaces are 320 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m2.The shaft rotates as 400 rpm. Taking the coefficient of friction as 0.06, calculate the power lost in overcoming the friction. Also, find the number of collars required for the bearing.
Problem: A double-threaded power screw with ISO metric trapezoidal threads is used to raise a load of 300 kN, The nominal diamter is 100 mm & the pitch is 12mm. The coefficient of friction at screw threads is 0.15. Neglect the collor friction. Q.45 Torque required to raise the load is
A vertical power screw with double start square threads of 50 mm mean diameter and 11mm pitch is raised against a load of 10 kN by means of a hand wheel, the boss of which is threaded to act as a nut. A thrust collar, taking up the axial load,supports the wheel boss and has a mean diameter of 60mm. The coefficient of friction is 0.18for the screw and 0.16for the collar. If the tangential force applied by each hand to the wheel is 200 N, find suitable diameter of the hand wheel.