Please solve and answer the question correctly please. Thank you f valuedifference Friction factor (f) inside the pipeline plays a major role for the selection ofthe pump power. To find the friction inside the pipe, the non-linear implicit4.equation is used =ed=−210g10 (25+257). Using this equation in Excel, find f3.7DRefvalue such that the difference between left-hand side of the equation equals andthe right hand side of the equation is on the order of 0.004 or less. The given valuesare & - = 0.0003, D = 0.254, Re = 7000. Try multiple values of f between 0.025and 0.045 and show your results in tabular form as well as graphical form asfollows:

Answered: Image /qna-images/answer/72513f62-2daa-4b03-bd55-10b32688461d.jpg

4. Friction factor (f) inside the pipeline plays a major role for the selection of the pump power. To find the friction inside the pipe, the non-linear implicit Using this equation in Excel, find f 2.51 3.7D Re equation is used += -2 log10 + value such that the difference between left-hand side of the equation equals and the right hand side of the equation is on the order of 0.004 or less. The given values are = 0.0003, D = 0.254, Re = 7000. Try multiple values of f between 0.025 and 0.045 and show your results in tabular form as well as graphical form as follows:

4. Friction factor (f) inside the pipeline plays a major role for the selection of the pump power. To find the friction inside the pipe, the non-linear implicit Using this equation in Excel, find f 2.51 3.7D Re equation is used += -2 log10 + value such that the difference between left-hand side of the equation equals and the right hand side of the equation is on the order of 0.004 or less. The given values are = 0.0003, D = 0.254, Re = 7000. Try multiple values of f between 0.025 and 0.045 and show your results in tabular form as well as graphical form as follows:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PROBLEM #1: Complete the data of the table below. Copy the entire table in your paper and use a different colored pen for your answers, you may also box your answers. Show solution. T:K P: kPa H: kJ/kg U: kJ/kg State (if wet steam provides xv as well) 1 525 350 2 125 2700 3 455.15 750 4 600 Xv = 0.8 5 200 1800 PROBLEM #2 A nozzle is used to increase the velocity of steam before it enters a turbine as a part of a power plant. The steam entering is at 1 MPa, 500 K and leaves at the conditions of 350°C and 2 MPa. If the nozzle has an inlet diameter of 3 cm and an outlet diameter of 1 cm, how much is transferred during the process? Is it lost or gained?
HANDWRITTEN AND FINAL ANSWER MUST BE IN ENGLISH UNITS. Show solution. An experimental gas turbine engine is under development to increase its mechanical efficiency. It has a turbine efficiency of 95% and compressor efficiency of 85%. The following parameters are provided: P1 = 550 kPa, T1 = 25 deg C, rp = 5.5, T3 = 1450 deg C, Wnet = 5500 kW. Compute for the (a) flow rate and (b) mean effective pressure. Consider Ethane as your working fluid.
Solve the following application problem: The model s(t) = -16?2 + 5? + 3 describes the height(in feet) of a diver at time ? is measured in seconds. Find the velocity of the diver when the diver hits the water.
Box your final answer and round to the nearest 2 DECIMAL PLACES. For the 2nd part, fill up the table of formulas below on a separate paper or index card • Four pounds of air gain 0.491 Btu/°R of entropy during a non- flow isothermal process. If P1 = 120 psia and V2 = 42.5 ft°, find a. P2, V1, and T1 b. Wn c. Q and d. Change in U. Process Isothermal Isentropic Polytropic Isometric Isobaric P-V and T-S diagram PV,T relations W W, C used for Q au ΔΗ AS
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. A pump discharges into a semi spherical tank at the bottom and cylindrical on top with a radius of 2 meters, and a total tank height of 8 meters. The flow rate is 80 gallons per minute and fluid specific gravity= 1.1. Determine the following: A) flow rate in kg/sec and time it takes to fill the tank in hours. Flow Rate and Time
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. A pump discharges into a semi spherical tank at the bottom and cylindrical on top with a radius of 2 meters, and a total tank height of 8 meters. The flow rate is 80 gallons per minute and fluid specific gravity= 1.1. Determine the following: A) flow rate in kg/sec and time it takes to fill the tank in hours. B) the weight in tons of the liquid if full tank local gravity is 32.1 ft/sec squared. C) volume of the tank in metric gallons. D.) how many drums will be needed to transfer all of the tank contents (tank being full) to the drums?
MECHANICAL ENGINEERING UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. SHOW THE STEP-BY-STEP PROCESS WITH SHORT COMMENT/EXPLANATION. ANSWER IN 4 DECIMAL PLACES. Two gaseous streams containing the same fluid enters a mixing chamber and leaves as a single stream. For the first gas the entrance conditions are A1=500 cm², v1=230 m/s, p1=1.60 kg/m³. For the second gas the entrance conditions are A2= 300 cm³, m2=8.84 kg/s, v2=0.502 m³/kg. The exit stream conditions is v3=130 m/s and v3=0.437 m3/kg. Determine the following: (a) the total mass flow leaving the chamber (kg/sec) (b) the velocity of the gas at 2. (m/sec)
a. CH, CQ and  are functions of CP. Draw the dimensionless performance curves of the turbine on a single graph by makingthe necessary scalings. (Fit the curve by using the excel program for drawing. Also give the values you used for plotting inthe table) b. Find the efficiency of the model at the most efficient operating point and the coefficients of head (CH), flow (CQ) and power(CP). Show them on the graph you have drawn. c. Calculate the diameter, net head, number of revolutions (rpm), flow rate, power (MW) and modified efficiency of theprototype d. Determine the turbine type ÖN number is 5
A cart weighing 0.5 kg is drawn up a smooth 45° incline by a motor, M, winding up a cable. The force in the cable can be expressed as 5t² N, where t is in seconds. When t = 0, the displacement s = 0 and the initial velocity is 3 m/s. Find the cart's velocity when t = 2 seconds. > Draw a very clear FBD of the cart that you can use to write the equations of motion > Write the equations governing the cart's motion along the incline. Use axes parallel and perpendicular to the incline. Find the velocity requested
Exponentials/Logarithms Q2 You are using an excavator on a cold winter day (20ºF outside) and the engine overheats (at about 220 °F). When you turn off the engine, it begins to cool down. The temperature T of the engine t minutes after you T-20 park satisfies the equation loge = -0.1 lt. 200 (a) Solve the equation for T. (b) Use part (a) and MATLAB, Excel, CAS calculator or an appropriate standard engineering software to find the temperature of the engine between 1 to 20 minutes. PC 1.1, 1.2, 1.3, 2.1, 2.3, 2.4, 2.5
Parts for each product Homework 1 n produce dryer plant Can for each product castiens Then each product is assembled in its dedicated washing and dryer A machines. Difterent are manufactured by press and motor ly sechon. The the monthly capacity of different sections are: washing machine or looo dryer machine Press section: 100 - Motor section: 1600 washing machine or 7o00 drjer machine machine assembly line: goo0 machine washing druer machine assembly line: 5000 machine washing 1, profit for each unct of washing and dryer machines is 270 and 300 respectively. Formulate a linear programming problem for Find ing how many washing and dryer machines should be produced many washing to maximize total plant's profit. 2.A A Post Company need to transfer 30000 boxes with two each truck presented of olifferent trucks. Chavactenistics problem for The table below. Formulate a linear programming each truck to optimum nunber of minimIze total Cost.
1- Calculate the piston travel, velocity, and acceleration for an engine with R= 50 mm and lo=170 mm using the equation and graphical representation and compare the results (take 45° increment ,N= 3000 r.p.m).