4) A pump discharges into a 3-m-per-side cubical tank. The flow rate is 300 liters perminute, and the fluid has a density 1.2 times that of water (density of water = 1000kg/m³). Determine a) the flow rate in kg/sec, and b) the time it takes to fill the tank.Things to consider upon checking your paper (rubrics):a) Identify the system (open or closed)b) What is the working substance? (if applicable)c) What is the process? (if applicable)d) Write your solutions clearly and orderly

Given data a=3 mQ=0.3 m3/sρ=1200 kg/m3

4) A pump discharges into a 3-m-per-side cubical tank. The flow rate is 300 liters per minute, and the fluid has a density 1.2 times that of water (density of water = 1000 kg/m³). Determine a) the flow rate in kg/sec, and b) the time it takes to fill the tank.

4) A pump discharges into a 3-m-per-side cubical tank. The flow rate is 300 liters per minute, and the fluid has a density 1.2 times that of water (density of water = 1000 kg/m³). Determine a) the flow rate in kg/sec, and b) the time it takes to fill the tank.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows from a large reservoir through a pipe system and into the atmosphere at the open end as shown below. The diameter of pipe A is 8 in. and the diameter of pipe B is 6 in. a) Determine the velocity at the open end of pipe B. b) Determine the flow velocity in pipe A if the flowrate through the system is constant. c) Calculate the minimum pressure in pipe B. The minimum pressure will occur at location "1" indicated with an arrow on the diagram below. d) Re-draw the diagram below. Sketch the energy and hydraulic grade lines on the re-drawn sketch. Choose four or five points throughout the system, and label each energy term (pressure head, velocity head, and elevation head) with numeric values at those points. Where you choose your points is up to you. Be sure to choose points that will provide the most information about the energy throughout the system. Show all your work. Include correct units in every step of your work. Use a ruler to draw straight lines. Color-code your lines…
4) A pump discharges into a 3-m-per-side cubical tank. The flow rate is 300 liters per minute, and the fluid has a density 1.2 times that of water (density of water = 1000 kg/m³). Determine a) the flow rate in kg/sec, and b) the time it takes to fill the tank.
2. A car is traveling on a highway at 28 m/s. a) What is the pressure at the bottom of a car's gas tank. that is a cube with side lengths of 0.5 meters? Assume the tank is full of gasoline with a denisty of 800 kg/m^3. b) How much pressure does a pump need to supply in order to draw gasloine from the bottom of the tank to the top of the tank? The velocity of the gasoline once it is pumped out of the tank should be 1 cm/s; the gas at the bottom of the tank is at rest. c) The gasoline from part b flows through a tube (cylinder) of radius lcm before entering a larger tube of radius 10cm. What will the velocity of the gasoline be in the larger tube? d) The tires on the car have an outer radius of 0.2 meters. How many complete rotations did the tires go through in one hour? Hint: Determine how far the car travels in one hour. e) How many hours can the car travel before running out of gas? f) During your journey. you hit a pothole and have to change your tire. You get your spare…
5. A human being has an average venous blood pressure of 12 mm Hg (Hg = mercury). The density of Hg (mercury) is 13,530 kg/m3. How high does a saline bag have to be raised to just barely equal to that of the blood in the vein) of saline through a line and needle inserted into a person's vein? The density of saline is 1020 enable the flow (that is, the pressure of the saline at the needle kg/m3.
Hello i have an example with an answer , please show the solution since only the answer was shown in this example. And i need its solution to review properly. Thank you 1. ) Question : A pump has a brake horsepower of 35 hp with an efficiency of 68%. Neglecting frictional losses, calculate the volume flow rate (m3/min) if the discharge is raised 60 meters above.Answer: 1.82
Topics: Fundamental of fluid flow A pipe transports 1962 N/s of water. The pipe tees into a 2"-diameterpipe and a 3"-diameter pipe. If the average velocity in the smaller-diameter pipeis 82 ft/s, calculate the flowrate (in ft^3/s) in the larger pipe.
Question 5 Water enters a fountain through a pipe with a cross-sectional area A₁ at a flowrate Q. The pressure in the inlet pipe is p₁. The water then leaves through a nozzle with a cross- sectional area A2 and at an angle 0, as shown in Figure Q5. Both the inlet and the nozzle are at a height h₂, and the jet reaches a maximum height h3. You may assume that viscosity is negligible. a) Find the horizontal force on the block
1. A pipe with a radius of 0.1 m used to drain an entire full water tank within one hour. The tank is a cylinder with a height (h) of 3 meters and a diameter of 5 meters.How fast will the water need to move through the pipe? Draw an illustration that will help you visualize the problem. Indicate important labels and measurements in your illustration.
A differential mercury manometer is used to measure the pressure drop across an orifice meter as liquid benzene flows steadily in a pipe. Sketch this system showing the section of pipe with the manometer and the orifice meter, showing your understanding of what these devices are. a) Taking the benzene to be flowing from left to right on your sketch, sketch the mercury in the manometer making it clear whether the mercury level in the left or the right arm would be higher. b) If this system is to accommodate benzene flow rates leading to pressure drops of up to 3.5 atm, at least how tall must the manometer be (in m)? That is, what is the maximum height difference in manometer fluid levels that needs to be measured?c) If the flowing fluid were to be air instead of benzene, would the mercury level difference in the manometer be larger, smaller, or the same as with the flowing liquid benzene? Briefly explain.
Benzene is flowing through a pipe at a rate of 140lb/hr. The specific gravity of benzene is 0.879. The outside diameter of the pipe is 2 inches and the thickness is 0.154 inch. Calculate the 1.)Velocity in ft/s 2.)Mass Velocity in lb/ft^2-s 3.)Volumetric flowrate in gal/min.
For the system determine a) the flow rate in m°/s b) The pressure at point A, B, c) the speed at the points CD. d) Build the diagrams of L.E and L.A.M.
Venturi meter as shown in Figure 2 has the cross-sectional area of 10 m² and 5 cm² at Point A and Point B, respectively. The height difference of the water levels in the two tubes is 16.2 cm. 61.2 cm B A Figure 2 Venturi meter a) What is the speed of water at Point A? b) What is the speed of water at Point B? c) What is the pressure difference between Point A and Point B? d) If the pressure at Point A is 15 kPa, what is the pressure at Point B?