4-75. Water flows into the tank through two pipes. At A the flow is 400 gal/h, and at B it is 200 gal/h when d= 6 in. Determine the rate at which the level of water is rising in the tank. There are 7.48 gal/ft.

4-75. Water flows into the tank through two pipes. At A the flow is 400 gal/h, and at B it is 200 gal/h when d= 6 in. Determine the rate at which the level of water is rising in the tank. There are 7.48 gal/ft.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q 1) Channel routing methods are often based on (a) the continuity of mass; (b) the continuity equa...

A: 1) Option b is the correct answer. Explanation - Channel routing methods are based on continuity equ...

Q: .500- 5.02 4.98 0.50 4.00±.02- 50 X 45° + 2.000 2. WHAT IS THE FARTHEST THE LEFT EDGE OF THE Ø.50 HO...

A: Farthest distance = (outer dimension - minimum distance of centre to centre hole)/2

Q: Q2/ Determine the amount of steel required to create a balanced condition for the beam that has heig...

Q: A soil sample taken from a field contains a volume of 110 m3 , weighs 220 grams when taken, and 165 ...

Q: he T-beam is subjected to diagram

Q: 2. Determine the wide beam shear stress at ultimate loads.

A: Ultimate load: -It is the amount of load applied to structure beyond which the structure will fail. ...

Q: 1. The bottom of a 3m diameter circular gate is 15m below the water surface. It is vertically submer...

A: To find out the resultant hydrostatic force on gate and magnitude of hydrostatic force due to water ...

Q: Type of annuity that is made at the beginning of each period, such as a rent payment Annuity Due Per...

A: An annuity is a series of payments made at equal intervals.

Q: 9. A cubic meter of a saturatod, normally consolidated clay has a dry mass of 4 kg and a porosity of...

Q: A soil sample taken from a field contains a volume of 110 cm3 , weighs 220 grams when taken, and 165...

Q: The weir below is to be built such that the estimated average flow over its crest will be Q = 3000 m...

Q: 1. What is the importance of road accident data systern? Solve the following a) A certain highway in...

A: Note- Hi! Thank you for the question As per the honor code, We’ll answer the first question since th...

Q: 4KN/m 10KN 8KN - 6m - 2m - 2m 4m 2m Using Moment Distribution Method: Draw Shear and Moment Diagram

Q: 5 B) Find y" for the function y =x + Vx at p(1,3)

Q: Four inelastic cables are attached to plate and hold the 1.25-ft- long spring A 0.25 ft in compressi...

A: Given Data -

Q: A 200 meter parabolic curve has a grade of -4% and +6%. The two grades intersect at 5+600 with eleva...

A: G1 = -4% G2 = 6% l = 200m

Q: ANSWER C ONLY ASAP

A: Time mean speed is the arithematic mean of speeds observed at some point in a specific time interval...

Q: A grain silo 3m x 3.6m is supported by floor beams which are 3m long. What depth of grains will 75mm...

A: Beam cross-section = 75 mm x 200 mm

Q: Determine the stresses for each segment when the temperature of the rigid bar is -45 degrees celsius...

A: solution as the temperatures decreases the material try to contract so inorder tensile stresses are ...

Q: Draw the shear and moment diagrams of the beam shown below. There is a fixed support at A, an intern...

A: We have given that -

Q: 4.0 The 800.0 kNcrate shown is in contact with a 45.0 ° incline plane. The coefficient of static fri...

Q: A soil sample taken from a field contains a volume of 110 cm3 , weighs 220 grams when taken, and 165...

Q: Determine the thrust block bearing areas for the conditions given below. Assume a maximum static pre...

A: F (Thrust Block) = 2PA*Sin∅2 {here, P is pressure, A is area ∅ is bend angle}

Q: Problem 6.87 The journal bearings at A and B only support vertical forces. The allowable bending str...

A: For the given shaft,

Q: (a) determine the maximum tension (Tmax) on the cable , (b) the cable diameter if the allowable tens...

A: Cable: - It is a flexible structure that support traverse loads by developing tensile resistance in ...

Q: Assume you are asked to advise the team that need to prepare the new quote for the construction of t...

A: HCD is human central design is a problem solving approach that's required you to put your customer n...

Q: Refer to the figure to answer the following questions: 150 kN/m2 45KN/m2 B 45KN/m? to 195 kN/m² 65° ...

Q: Give expanation to how we got.335 kip/itand why?

A: For the given steps, the explanation for obtaining 1.335 kip/in has to be given.

Q: HI = 1.496 ELEVATION OF PT A: = 200 K = 99 HAIR READING MIDDLE LOWER 1.589 VERT. STADIA DISTANCE STA...

Q: pressure (MN/m2) of a round vith 50 mm diameter and a t of 3mm? Assume that the bo ail with the gene...

A: Given data- Diameter (D) = 50mm Thickness (t) = 3mm Tensile stress(S) = 35 MN/m²

Q: 20KN 8m 6m Using Cantilever Method: Compute for the axial load at BD, shear at CD and moment at A 40...

Q: Determine the deflection at point B given the cross-section of the beam and assuming E = 200 GPa. 20...

A: Given Data: Flange width B = 200 mm Flange thickness tf = 20 mm Depth of Section D =200 mm Web thic...

Q: A 2 in. 2 in. 2 in. Determine the force P needed to support the 140-lb weight(Figure 1) . Each pulle...

A: To find: chord reation at A and B.

Q: For a colony of 10,000 persons having sewage flow rate of 200 1/capita/day, BOD of applied sewage is...

Q: Please help. Do not just guess. Prove your answer. I will give a good feedback. thank you :)

A: Step 1: a) Answer: The maximum flexural stress is the outermost fiber of the outside diameter when...

Q: The beam of the cross section in the form of American standard Channel or C shape C10 x 30 is clampe...

A: The moment is linearly proportional to the bending tensile stress, and y is a unit dimension in the ...

Q: Calculate the porosity of a sandstone sample (in percent) that has 4 cubic centimeters of void space...

A: Introduction : Porosity is defined as the ratio of volume of void space upon total rock volume Given...

Q: 7. For the Pitot Tube below, determine the height that the fluid rises, L, in the column if water is...

A: Velocity of flow through pitot tube is given and it has been asked to determine height of fluid rise...

Q: Two masses are attached to a uniform meter stick as shown in the figure below. The masses of m1 and ...

Q: Estimate the total consolidation settlement (primary & secondary) after 2 years and 3 months after t...

A: We have to determine the value of total consolidation settlement after 2 year and 9 months after the...

Q: In 1: 20 model of a spillway, the velocity and discharge are 1.5 m/sec and 2.0 m/sec respectively. F...

Q: 24KN/m 200KN B 6m 4m 4m 8m Using Moment Distribution Method: Draw Shear and Moment Diagram D.

Q: ngents converge at an angle of 30°, the direction of the second tangent is due east. The vertical di...

Q: ?Determine the reaction at points A and C. Member BC is pin-connected at both ends. (Partial ans. Ax...

Q: PROBLEM 1. Calculate the uniform live load capacity of the reinforced concrete beam in Figure 1 if f...

A: Given, f'c=20 MPa=3002.281 psify=276 MPa=40030.4 psi DL=680 N/m B=250 mm=9.84 inch. d=460 mm=18.11 i...

Q: Distance between the two points Pand Q was required to be determined from tacheometer fitted with an...

Q: the de

A: Given: A992 steel with gross area of 10 in2. KLx/rx =60 and KLy/ry = 80 To find the design column s...

Q: If a four legged roundabout has 8 conflict points, how many does a 3 legged roundabout?

A: Roundabout is circular intersection which allows slow and safe traffic flow around the central islan...

Q: The value of stress produced due to 30 N is 44 N/mm2. Determine the cross sectional area of rod

A: This question is related to the Strength of Material. In this problem we calculate cross section are...

Q: Two parallel tangents 10 m apart are connected by a reversed curve. The chord length from the PC to ...

Question

Fluid

4-75. Water flows into the tank through two pipes. At A
the flow is 400 gal/h, and at B it is 200 gal /h when d = 6 in.
Determine the rate at which the level of water is rising in
the tank. There are 7.48 gal/ft'.
-3 ft
8 in.
Prob. 4-75

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2-17. The tank is filled with aqueous ammonia (ammonium hydroxide) to a depth of 3 ft. The remaining volume of the tank contains air under absolute pressure of 20 psi. Determine the gage pressure at the bottom of the tank. Would the results be different if the tank had a square bottom rather than a curved one? Take pm = 1.75 slug/ft'. The atmospheric pressure is pam = 14.7 lb/in. 3 ft Prob. 2-17
5. A closed cylindrical tank mcasurcs 12ft. long and 5ft. in diameter. It has to contain water with a depth of 3ft when the tank is lying in horizontal position. Find the height of the water when the tank is in its vertical position. 12'
F4-1. Water flows into the tank through a rectangular tube. If the average velocity of the flow is 16 m/s, determine the mass flow. Take p, 1000 kg/m'. 16 m/s 50 mmy 60 0.06 m (0.05 m) sin 60
4. Evaluate the pressure at the center of pipe A. Given: y of Liquid 1 = 12 kN/m y of Liquid 2 = 25 kN/m. hi = 60 cm h2 = 10 cm L = 60 cm а. -750 Рa c.-650 Pa b. -800 Pa d. -700 Pa Liquid 1 Liquid 2 h, h2
Q3. Water flows through pipes A and B. Lubricating oil is in the upper portion of the inverted U, Mercury is in the bottom of the manometer bends. Determine the pressure difference, pA-pB in units of kPa. B Oil 0:25 m 25 cm H,0-10 cA H,0 20 cA 507 13 cn 15 Rotm
Water flows steadily through a nozzle at 60 kg/s. the diameters are D1 = 220 mm and D2 = 80 mm. Compute (a) the volume flow rate (m^3/s) (b) the velocity at section 1 (m/s) (c) the velocity at section 2 (m/s). , D1 D2
5-9 A 0.75-m³ rigid tank initially contains air whose den- sity is 1.18 kg/m³. The tank is connected to a high-pressure supply line through a valve. The valve is opened, and air is allowed to enter the tank until the density in the tank rises to 4.95 kg/m³. Determine the mass of air that has entered the tank. 2.83
1) Determine the flow in Ips on the orifice between the 2 tanks shown below AIR 25kPa AIR 10kPa OIL S=0.80 OIL S=0.80 WATER WATER ORIFICE C0 60 D-50mmo 2,8m 2m 1.5m WL
4.80 Water (p = 62.4 lbm/ft³) flows from the large orifice at the bottom of the tank as shown. Assume that the flow is irrotational. Point B is at zero elevation, and point A is at 1 ft elevation. If VA = 4 ft/s at an angle of 45° with the horizontal and if VB = 12 ft/s vertically downward, what is the value of PA - PB? Answer B Vertical Problem 4.80 45°
Determine the rate of flow of water through a pipe of 300 mm diameter placed in an inclined position where a venturimeters is inserted, having a throat diameter of 150 mm. The difference of pressure between the main and throat is measured by a liquid of sp. gravity 0.7 in an inverted U- tube which gives a reading of 260 mm. The loss of head between the main and throat is 0.3 times the kinetic head of the pipe. Liquid (Sp. gr. = 0.7) y= 260 mm Inlet - Throat Water (Sp. gr. = 1.0)
A pump draws water from a reservoir A and lifts it to reservoir B as shown. The loss of head from A and lifts it to reservoir B as shown. The loss of head from A to (1) is 5 times the velocity head in the 12-inch pipe and the loss of head from (2) to B is 23 times the velocity head in the 7-inch pipe. Compute the pressure heads (2) in ft when the discharge is 447 gpm. Round your answer to 2 decimal places.
Find the time it takes to decrease the water level in the tank 1 by 1.5m. Use C = 0.60 T. h.. 2.3m do: 300mn * 2m 454 45 Gm