4-59. The post is made from 6061-T6 aluminum and has a diameter of 50 mm. It is fixed supported at A and B, and at its center C there is a coiled spring attached to the rigid collar. If the spring is originally uncompressed, determine the compression in the spring when the load of P = 50 kN is applied to the collar. 0.25 m 0.25 m P HUNI A C k = 200 MN/m B Probs. 4-58/59

4-59. The post is made from 6061-T6 aluminum and has a diameter of 50 mm. It is fixed supported at A and B, and at its center C there is a coiled spring attached to the rigid collar. If the spring is originally uncompressed, determine the compression in the spring when the load of P = 50 kN is applied to the collar. 0.25 m 0.25 m P HUNI A C k = 200 MN/m B Probs. 4-58/59

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.8.3P

See similar textbooks

Similar questions

5 - The ring supports the 1000-N load and is held in position by the two cables attached to vertical walls . Find the tensions T1 and T2 by at least two different ways . 1C00 N
25 KN Using the method that has been covered, find the displacement of the node 2 if E1 = 100 GPa and A1=10-6 m² and E2= 200 GPa and A2=2x10 6 m². N2 5 cm 2 30° N3 N1, Note: The stiffness matrix of individual elements should be first written, then the equilibrium equations at each node should be written, expanded in terms of nodal displacement, and used to perform the assembly of the global stiffness matrix of the problem. Then, the appropriate boundary conditions should be applied and the nodal displacement vector should be found. Every step should be shown; missing any step would result in point deduction even if the final answer is correct
3-14. The rigid pipe is supported by a pin at A and an A-36 steel guy wire BD. if the wire has a diameter of 6 mm, determine how much it stretches when a load of P= 3 kN acts on the pipe. 1.2 m -0.9 m- 0.9 m
The helical compression spring is made of 12mm wire diameter with 132 mm mean diameter. Determine stiffness of the spring when modulus of rigidity G=80 kN/mm2,number of turn is 13 and axial load is 190N.
ZTE The light boom AB IS attached to g vertical point a force Pis applied Wall by a ball and socket at A and Suppore by two cable> at B.a where P= 14i-12) KN Note that the at B force at A two -force member Calculate the magntude reaction a cts a cts along the boonm because it rs of the force reaction at A in kN. key 2m. meters 4M- 3. 6 m A b take sum forces at point B, Sum the veetor in 1,J,K and so lue the simaltaneous equation involuing BD BC and AD he
The truss is supported by a pin at A and a roller at B. Determine the support reactions. The truss is supported by a pin at A and a roller at B. Determine the support reactions. 0.1N kN -2 m- 4 m 2 m P kN 4 m 450 P = 5 N = 100
6-45 A rope and pulley system is used to support a body as shown in Fig. the ropes are continuous over the pulleys. Determine the force P required to hold the body in equilibrium if the weight W of the body is 400 lb. Each pulley is free to rotate, and P W
The rigid bar of negligible weight is supported as shown. The middle helical spring is made of 22 mm diameter steel spring and has an outside diameter of 100 mm with 10 turns and the two side springs are made of 32 mm steel spring and has an outside diameter of 250 mm with 8 turns. Before the load P is applied, the side springs are 25 mm longer than the middle spring. If the applied load P = 15 kN and the rigid bar remains horizontal, determine the stress in each spring. Use G = 83 GPa for steel and G = 42 GPa for bronze.
6-23. The Fink truss supports the loads shown. Determine the force in each member and state if the members are in tension or compression. Approximate each joint as a pin. Problem 6-23 1000 lb 500 lb 2.5 ft eo ec 00 00 30° 1000 lb 2.5 ft B 80.00 GO OC H 1000 lb 2.5 ft 8000 co C 500 lb 2.5 ft G D F E 30°
Determine the support reactions: 4 m 4 m 150 KN 6 m 25 kN/m -10 m- Diag 4m T 4m Ax ISC
A d E D B d C PV d d/2 d/2 Find the reaction forces and pin joint E and roller A given P = 900 N. Also determine the largest tensile and compressive members.
6-103 A bar is loaded and supported as shown in Fig. End A of the bar is supported with a ball-and-socket joint and end B with a cable and a link. Determine the com- ponents of the reaction at supports A and B and the ten- sion T in the cable. 3 ft 500 Ib 8 ft 4 ft A B 750 lb 00