33. State whether each of the following conversions is possible or impossible and WHY. For any examples that are possible, perform the conversion and report your answer to the correct number o significant figures. (a) 20. mL (b) 2 mL (c) 10. m³ cm² m³ in. ft² (d) 3 mm² (e) 10. lbs. of aluminum → cm³ (Hint: This one IS possible).

33. State whether each of the following conversions is possible or impossible and WHY. For any examples that are possible, perform the conversion and report your answer to the correct number o significant figures. (a) 20. mL (b) 2 mL (c) 10. m³ cm² m³ in. ft² (d) 3 mm² (e) 10. lbs. of aluminum → cm³ (Hint: This one IS possible).

Introductory Chemistry: A Foundation

9th Edition

ISBN:9781337399425

Author:Steven S. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Donald J. DeCoste

Chapter15: Solutions

Section: Chapter Questions

Problem 3CR

See similar textbooks

Similar questions

How do you distinguish (a) chemical properties from physical properties? (b) distillation from filtration? (c) a solute from a solution?
Suppose that you are closing a cabin in the north woods for the winter and you do not want the water in the toilet tank to freeze. You know that the temperature might get as low as 30. C, and you want to protect about 4.0 L water in the toilet tank from freezing. Calculate the volume of ethylene glycol (density = 1.113 g/mL; molar mass = 62.1 g/mol) you should add to the 4.0 L water.
What is the difference between (a) mass and density? (b) an extensive and an intensive property? (c) a solvent and a solution?
hat do the coefficients of a balanced chemical equation tell us about the proportions in which atoms and molecules react on an individual (microscopic) basis?
A solution made by dissolving sugar in water is homogeneous because the composition is the same everywhere. But if you could look with very high magnification, you would see locations with water particles and other locations with particles of sugar. How can we say that a sugar solution is homogenous?
Particles in the illustration below undergo a chemical change. Which among the remaining boxes, a through d, can represent the products of the chemical change? If a box cannot represent the products of the chemical change, explain why. a b c d
What properties distinguish solids from liquids? Liquids from gases? Solids from gases?
7. Suppose you make a solution that contains 17.59 g of sodium chloride and 960 g of water. (a) What is the mass % of sodium chloride? (b) If 16.47 mL of your solution weighs 16.651 g,what is the density (in g/cc)?
5 Water is evaporated from the magnesium chloride solution. The resulting solid is melted at 700°C and decomposed by passing electric current through it. (a) What is the name of the physical change that occurs first in the magnesium chloride? (b) Write the balanced chemical equation for this step. (c) Identify the type of chemical reaction.
A geochemist measures the concentration of salt dissolved in Lake Parsons and finds a concentration of 11.10 g.L-¹. The geochemist also measures the concentration of salt in several nearby non-isolated lakes, and finds an average concentration of 4.30 g⋅L¯¹. Assuming the salt concentration in Lake Parsons before it became isolated was equal to the average salt concentration in nearby non-isolated lakes, calculate the percentage of Lake Parsons which has evaporated since it became isolated. Be sure your answer has the correct number of significant digits.
Decide whether each proposed multiplication or division of measurements is possible. If it is possible, write the result in the last column of the table. proposed multiplication or division Is this possible? result 480. mg O yes = ? 0.080 g O no O yes (3.0 g) · (0.029 kg) = ? O no O yes (7.0 m) · (6.0 s) = ? O no O Ooo
An aqueous solution of sodium chloride,NaCl , is made by dissolving 1.01 grams of sodium chloride in sufficient water in a 50.0 mL volumetric flask, and then adding enough water to fill the flask to the mark. What is the weight/volume percentage of sodium chloride in the solution? Weight/volume percentage = %