33 Elev A Water Elev C Turbine Elev B Water flows from Reservoir A (Elev 128 ft.) to a turbine (Elev 73 ft.) then discharges into tailtrace B (Elev 24 ft.) as shown. The head loss from (A) to (1) is 3 times the velocity head in the pipe, and the head loss from (2) to (b) is 0.64 times the velocity head in the pipe. If the flow rate in the pipe is 35 f13/s, diameter of all pipes is 24 in, calculate the horsepower generated by the turbine. Use 1 hp = 550 lb-ft/s. Round off to the nearest whole number. Question 33 of 48> A Moving to another question will save this response.

33 Elev A Water Elev C Turbine Elev B Water flows from Reservoir A (Elev 128 ft.) to a turbine (Elev 73 ft.) then discharges into tailtrace B (Elev 24 ft.) as shown. The head loss from (A) to (1) is 3 times the velocity head in the pipe, and the head loss from (2) to (b) is 0.64 times the velocity head in the pipe. If the flow rate in the pipe is 35 f13/s, diameter of all pipes is 24 in, calculate the horsepower generated by the turbine. Use 1 hp = 550 lb-ft/s. Round off to the nearest whole number. Question 33 of 48> A Moving to another question will save this response.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

El. 200 m A Res. H-W L Pipe B pipec →Negleet minor losses → Pipes B, C, and E are all have: Pipe E = 600 m long d = 500 mm f = 0.03 → When the Pump develops 15m of head, the Velocity in pipe C is 5 m/s. Find : a) the flowrate in all pipes. b) the elevation of the discharg end of Pipe E.
Elev A Water Elev C Elev B Water flows from Reservoir A (Elev 138 ft.) to a turbine (Elev 75 ft.) then discharges into tailtrace B (Elev 26 ft.) as shown. The head loss from (A) to (1) is 4 times the velocity head in the pipe, and the head loss from (2) to (b) is 0.96 times the velocity head in the pipe. If the flow rate in the pipe is 34 ft3/s, diameter of all pipes is 26 in, calculate the horsepower generated by the turbine. Use 1 hp = 550 lb-ft/s. Round off to the nearest whole number.
1. Two tanks A and B have 70 m difference in water levels, and are connected by a pipe 0.25 m diameter and 6 km long with 0.002 friction coefficient. The pipe is tapped at its mid point to leak out 0.04 m3/s flow rate. Minor losses are ignored. (a) Determine the discharge leaving tank A? (b) Find the discharge entering tank B? ha А he B Q3 h = 70 m
In the branched pipe system shown, 850 L/min of water at 10°C is flowing in a DN 100 Schedule 40 pipe at A. The flow splits into two DN 50 Schedule 40 pipes as shown and then rejoins at B. Calculate (a) the flow rate in each of the branches and (b) the pres- sure difference PA PB. Include the effect of the minor losses in the lower branch of the system. The total length of pipe in the lower branch is 60 m. The elbows are standard.
Water flows from Resorvoir A (Elev 133 m.) to a turbine (Elev 76 m.) then discharges into tailtrace B (Elev 30 m.) as shown. the head loss from (A) to (1) is 2 times the velocity head in the pipe, and the head loss from (2) to (b) is 1.49 times the velocity head in the pipe. if the flow rate in the pipe is 35 ft63/S, diameter of all pipes is 25 in., calculate the horsepower generated by the turbine. Use 1 hp = 550 lb-ft/s.
Water flows from Reservoir A (Elev 125 m.) to a turbine (Elev 67 m.) then discharges into tailtrace B (Elev 26 m.) as shown. The head loss from (A) to (1) is 2 times the velocity head in the pipe, and the head loss from (2) to (b) is 1.97 times the velocity head in the pipe. If the flow rate in the pipe is 39 ft3/s, diameter of all pipes is 30 in, calculate the horsepower generated by the turbine. Use 1 hp = 550 lb-ft/s. ANS : 1,000,000
Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E
QI/ Water flows from the reservoir on the left to the reservoir on the right at a rate of 0.45 ms. The formula for - Ekevation? the head losses in the pipes is h - 0.02 L: D 2g What elevation in the left reservoir is required to produce this flow? Also carefully sketch the HGL and the EGL for the system. Note: Assume the head-loss formula can be used for the smaller pipe as wel as for the Elevation 34 m 80 m 90 m D, =0.344 m A, -0.1 m D,= 0.486 m A- 02 m larger pipe. Q2/ A horizontal pipe carries cooling water at 10°C for a thermal power plant. what is the pressure in the pipe at L= 2000 m? The head loss in the pipe is 0.02(L/D)V + Eerhm- 0n -D02m 28 Detn where Lis the length of the pipe from the reservoir to the point in question, V is the mean velocity in the pipe, and Elvation =m L-2000m (2. Dis the diameter of the pipe. The pipe diameter is 20 cm and the rate of flow is 0.06 mls, Q3/ For the parallel-pipe system of L-250 D-3 in Fig. each pipe is cast iron, and the pressure drop p -…
Qs/Three pipes No. (1), (2) and (3) are connected in series as shown in Figure No. (4). Find flow rate fro Reservoir A to Reservoir B. Physical properties of the pipes are listed in Table below. Pipe Length of Pipe Diameter of Pipe Coefficient of friction No. L d. f (mm) | (mm) 1 300 300 0.019 150 200 0.021 250 250 0.02 Resaros A 180(m) Pipeci) Pipery Resemi PipeC) -~3
A A 1 2 B The three-reservoir system is shown below: 3 The elevation of Reservoir at A is 140m and at Cis 50m. The flow rate at Pipe 1 from Reservoir A is 1.75 m/s. All pipes have a length of 500 meters, friction factor f - 0.02, and sizes namely: Pipe Diameter 1 (mm) - 600mm Pipe Diameter 2 (mm) = 500mm Pipe Diameter 3 (mm) = 400mm Determine the Headloss at Pipe 3 in meters.
Problem 2(1 For the series/parallel pipe system shown, determine the flow rate in pipe 4 if the total head loss in the system is 30 m. Diameters are in mm and pipe lengths in m. n=0.012 D,=350 L=2500 B n=0.013 D;=300 L=1200 n=0.011 С п-0.011 D n=0.012 E A. D=500 L,=1000 D3=300 L,=800 D=600 L,=1200 n=0.012 D=350 L=1500
Problem 7: The two pumps in problem 6 are now arranged in parallel. The static head is 40 ft. The pipe diameter is 9-in of 1200 ft length and the minor loss coefficient is 20. Determine the operating condition and power output (Q, head, and efficiency) and the power output for the system of two pumps. Use f= 0.022. What is the flow rate and efficiency of each pump?