3. The upward flow of water through a layer of sand in the tank shown in figure has the following properties: e =0.50, G=2.67. Determine the following: a) Effective stress at point A b) Effective stress at point B c) Upward seepage force per unit volume of soil 0.8m 3.5m Supply of Water 0.5m A B 1.9m

3. The upward flow of water through a layer of sand in the tank shown in figure has the following properties: e =0.50, G=2.67. Determine the following: a) Effective stress at point A b) Effective stress at point B c) Upward seepage force per unit volume of soil 0.8m 3.5m Supply of Water 0.5m A B 1.9m

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.13P: Repeat Problem 10.12 for q = 700 kN/m2, B = 8 m, and z = 4 m. In this case, point A is located below...

See similar textbooks

Similar questions

3.11 An oil storage tank that is circular in plan is to be constructed over a layer of sand, as shown in Figure P3.5. Calculate the following settlements due to the uniformly distributed load g of the storage tank: 9 (a) The elastic settlement below the center of the tank at z = 0 and 3m. (b) The elastic settlement at (i) z = 1.5m, s = 0; (ii) z = 1.5m, s = 3m. Assume that v = 0.3, E = 36MN/m², B = 6m, and q = 145kN/m² Diameter 8- Center line TE Sand Unit weight - Y Poisson's ratio = v Modulus of clasticity = Ez Figure P3.5
Magnitude and angle of inclination (from horizontal) of the major and minor principal stresses. 5. A sample of soil is subjected to a stress system as shown in the figure. Determine, a. Maximum shear stress. Stress on a horizontal plane. 5 kN b. с. 10 cm |309 1 kN 20 cm 1 kN 3 kN 20 cm
Refer to Figure P3.3 Attached. Use Eqs. (3.10) and (3.11) attached to determine the variation of OCR and preconsolidation pressure σ'c.
5-4 For the given soil profile and the piezometric surfaces measured at the top of the two sand and gravel layers, determine the pore pressure and effective stress at points A, B, C, D, and E. Piezometers 2 m Ground surface 2 m Sand y = 18 kN/m3 Water table y_ 11m Y = 20 kN/m3 A 4 m Clay Y = 18 kN/m3 加。B 1Im 5 m Sand and gravel y = 22 kN/m3 2 m •D 5 m Clay Y = 19 kN/m3 Sand and gravel y = 23 kN/m3 %3D Cpyright by
Problem 4 Consider the upward flow of water through a layer of sand in a tank as shown in the figure. Properties of sand: Void ratio e = 0.52 Specific gravity of solids = 2.67 1. Calculate the effective stress at B. 2. What is the upward seepage force per unit volume of soil? 3. What is the rate of upward seepage of water in m³/hour if K = 2 x 10-³ m/sec and area of tank is 0.45 m²? h=1.5 0.70 m 2 m In flow Ysat H₂o valve open 1 m
B) State whether the sentence is true or false (answer 5 only). 1. The preconsolidation stress seprates between the overconsolidated state and normal consolidated state. 2. The soil may consolidate when the ground water table level rise up. 3. In flownet, the head loss in each drop is constant. 4. In flow net, the equipotential lines represent lines of equal potential. 5. The shear strength of granular material is affected largely by the initial void ratio. 6. Drained triaxial compression test means that the soil specimen is dry.
Refer to Figure P3.2. Vane shear tests were conducted in the clay layer. The vane (tapered) dimensions were 63.5 mm (d) x 127 mm (h), iB = iT = 458 (see Figure 3.23). For the test at A, the torque required to cause failure was 51 N ? m. For the clay, given: liquid limit = 46 and plastic limit = 21. Estimate the undrained cohesion of the clay for use in the design by using Bjerrum’s l relationship [Eq. (3.40a)].
A soil profi le consists of a clay layer underlain by a sandlayer, as shown in Figure P7.17. If a tube is inserted intothe bottom sand layer and the water level rises to 1 mabove the ground surface, determine the vertical effective stresses and porewater pressures at A, B, and C. IfKo is 0.5, determine the lateral effective and lateral totalstresses at A, B, and C. What is the value of the porewater pressure at A to cause the vertical effective stressthere to be zero?
Q1 A 25 m thick layer of clay is underlain by a layer of silt, as shown in the Figure. 1. Determine the effective stress at point A when Z=3 m. 2. Determine the effective stress at point B when h=3 m. 3. By changing h and Z, would you expect that the effective stresses at A and B can have the same value? WIZ 1² W.T 12 m B Clay e=0.6, G.-2.69 Clay w=30% Silt w=50%, G, 2.70
An embankment load on a silty clay soil layer as shown below. Determine the stress increase under the embankment at points A and B that are loaded at a depth of 6 m below the ground surface. Prob. 5 m 1H:2V 1H:2V 1H:1V 8 m Y=18 kN/m y=18 kN/m 6 m : B A
N B 0 Horizontal The stresses shown in the figure are applied at a point in a dry clayey sand soil mass. A= 50 kPa and B= 125 kPa The shear strength parameters of the clayey sand are: c'= 9kPa and p'=29° 0=30° a) The value of the shear stress, T, is slowly increased. What value would cause shear failure at this point (in kPa)? b) At failure, what angle does the failure plane make with the horizontal (in degrees)?
1. Three point loads, 19000, 20000 and 18000kN, act in line 8 m, 6m apart near the surface of a soil mass. Calculate the vertical stress at a depth of 4m vertically below the center (30000kN) load. 19 000 KN 20 000 kN 18 000 KN Influence factors for vertical stress due to point load ↳ riz b riz 1₂ 0.478 0.80 0.139 0.020 0.466 0.90 0.108 0.016 0.433 1.00 0.084 0.013 4 m 0.385 1.10 0.066 0.011 0.329 1.20 0.051 0.009 0.273 1.30 0.040 0.006 0.221 1.40 0.032 0.004 0.176 1.50 0.025 0.003 8 m 6m riz 0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 1.60 1.70 1.80 1.90 2.00 2.20 2.40 2.60