3. Consider an isotropic harmonic oscillator in two dimensions. The Hamiltonian is given by: 門+,1。 (a) What are the energies of the three lowest-lying states? Is there any degeneracy? (b) Apply a perturbation V - ómuXY, where 6 is a dimensionless real mumber much smaller than unity. Find the zeroth-order energy eigenket and the corresponding energy to first order (that is, the unperturbed energy obtained in the previous part plus the first-order energy shift) for each of the three lowest-lying states. (c) Solve the Ho + V problem exactly. Compare with the perturbation results obtained in the second part.

3. Consider an isotropic harmonic oscillator in two dimensions. The Hamiltonian is given by: 門+,1。 (a) What are the energies of the three lowest-lying states? Is there any degeneracy? (b) Apply a perturbation V - ómuXY, where 6 is a dimensionless real mumber much smaller than unity. Find the zeroth-order energy eigenket and the corresponding energy to first order (that is, the unperturbed energy obtained in the previous part plus the first-order energy shift) for each of the three lowest-lying states. (c) Solve the Ho + V problem exactly. Compare with the perturbation results obtained in the second part.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q6. Figure Q6 shows a modulated waveform v(t) in microvolts as a function of time t in nanoseconds. 25 50 75 100 125 150 175 200 225 250 50 40 40 30 30 20 20 10 10 -10 -10 -20 -20 -30 -30 -40 -40 -50 -50 250 25 50 75 100 125 150 175 200 225 time/ns Figure Q6: Modulated waveform (a) Describe the modulation scheme. (b) What are the values of the carrier frequency and the modulation frequency? (c) What is the value of the modulation index? (d) What is the transmission efficiency (ratio of modulated to total power) in this example? (e) Sketch the spectrum of this modulated waveform indicating the relative magnitudes of the various spectral components. (f) The modulating wave in this example is substituted with a square wave of 50% duty cycle and of fundamental frequency 1.0 MHz. Sketch the absolute value of the spec- trum of the modulated waveform indicating the frequencies and relative magnitudes of the sideband components. (g) Demodulation of this type of signal is usually accomplished…
If the TIME/DIV is set to 0.2 ms, what is the time constant of the circuit? X ms An oscillator with a natural frequency of 380 Hz is driven by a 580 Hz sinusoidal signal. At what frequency does it oscillate?
Explain the working of 3 stage RC phase shift Oscillator. Design a 5 stage RC phase shift oscillator to generate a 300Hz sinusoid. Assume the capacitance used is 3pF
An AM wave displayed on an oscilloscope has values of Vmax = 4.8 and Vmin = 2.5 as read from the graticule. What is the percentage of modulation? (Our lesson is An AMPLITUDE MODULATION FUNDAMENTALS) (I need clear solution and symbol)
3. Regarding the plotted waveform below: (a) Does it have dc symmetry? (b) Does it have even symmetry? (c) Does it have odd symmetry? (d) What is its period? (e) What is its angular frequency? (f) What is its oscillation frequency? (g) What is a piecewise expression V(t) for one period? 11-10-9 4 VI A 10 12 3 2 H -H -2 -3 8 9 10 11 12 1
Q/ Discuss how you can convert the square wave into the sinewave of fundamental frequency.
A step up chopper is used to feed a load at 400 V dc from a 250 V dc source. The inductor current is continuous. If the off time of switch is 20 microsec, the switching frequency of the chopper in kHz is ?
3- Analyze the system shown below to find the output waveform, Vout, assume the capacitor voltage value is -1.0 V at t-0 and RC-1 msec. -0.5 -1.0 V(1), V 1.0 0.5 R $ AAA f, msec
Is it more efficient if the transient response is high or is it more efficient if the transient response is low/short in RL Circuit? Kindly explain it to me, thank you!
A carrier signal with frequency of 1 MHz and peak-to-peak amplitude of 10√2v is added to a single tone message with frequency of 1 kHz and peak-to-peak amplitude of 4√2v. Then passed through a diode having the following c/cs: i(t) = e(t) + 0.5e²(t), find: 1- Modulation depth of DSB signal. 2- Frequency of each component in the diode current.
1) what is the fundamental frequency (in units of Hz) of the given signal is 2)The period of the given signal is 3)The harmonic frequencies (in unit Hz) of this signals are
-Consider the following DT sequence, Is this signal as Power Signal or Energy signal? Determine it. * 0Snくs X [n ]= lo-n 55.n510 • ther wise Power Signal, P=85 Energy Signal, E=85 O Neither energy nor Power O Both, P=30 E=55 -Is the following signal is X(4) - Sin 3t + Sin 大t Periodic Aperiodic