3. At three winding transformer at no-load case, the current flows through the tertiary windings is large current load current secoundary current no-current 4.We can correct P.f (Power Factor) by using: * impedance Inductance capacitance non 5. There are two basic types of capacitor installations which used in power factor correction which are: used in power factor correction which are: series, shunt series, individual individual capacitors, and banks of fixed or automatically switched capacitors.

3. At three winding transformer at no-load case, the current flows through the tertiary windings is large current load current secoundary current no-current 4.We can correct P.f (Power Factor) by using: * impedance Inductance capacitance non 5. There are two basic types of capacitor installations which used in power factor correction which are: used in power factor correction which are: series, shunt series, individual individual capacitors, and banks of fixed or automatically switched capacitors.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Similar questions

A bank of three single-phase transformers, each rated 30MVA,38.1/3.81kV, are connected in Y- with a balanced load of three 1, Y-connected resistors. Choosing a base of 90MVA,66kV for the high-voltage side of the three-phase transformer. spify the base for the low-voltage side. Compute the per-unit resistance of the load on the base for the low-voltage side. Also, determine the load resistance in ohms referred to the high-voltage side and the per-unit value on the chosen base.
An ideal transformer has no real or reactive power loss. (a) True (b) False
In per-unit equivalent circuits of practical three-phase transformers, under balanced thr-phase operation, in which of the following connect ions would a phase-shifting transformer come up? (a) Y-Y (b) Y- (c) -
Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.
For developing per-unit equivalent circuits of single-phase three-winding transformer, a common Sbase is selected for all three windings and voltage bases are selected in proportion to the rated voltage of the windings (a) True (b) False
The ideal transformer windings are eliminated from the per-unit equivalent circuit of a transformer. (a) True (b) False
A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1
ََQ/ 400/200 V, single-phase transformer is supplying a load of 50A at a power factor of 0.866 lagging. The no-load current is 2A at 0.208 p.f. lagging. .. Find The primary current is ...... A * The primary power factor is ........ lagging *
Write the short notes on Reactive Power compensation for test transformer. (Submit Through Turnitin via Moodle)
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
The primary of a certain transformer takes 1 A at a power factor of 0.4 when connected across a 230 V, 50 Hz supply and the secondary is on open circuit. The number of turns on the primary is twice that on the secondary. A load taking 50 A at a lagging power factor of 0.8 is now connected across the secondary. Sketch, and explain briefly, the phasor diagram for this condition, neglecting voltage drops in the transformer. What is now the value of the primary current?
Three transformers, e ach rated 25 MVA, 38. 1 /3.81 kV, are connected Star – Delta with a balanced load of three 0.79 ohm (load resistance RL) star connected resistors. Choose a base of 75 MVA, 66 kV for the high-voltage side of the transformer and specify the base for the low-voltage side. Determine the per-unit resistance of the load on the base for the low-voltage side. Then, determine the load resistance RL in ohms referred to the high-voltage side and the per-unit value of this resistance on the chosen base.