3. Ana, Ben and Cathy are on different locations on the ground. The bearing of Ana from Ben is 40°T. The bearing of Cathy from Ana is 130°T. If the distance between Ana and Ben is 12km and the distance between Ana and Cathy is 10km, find the distance between Ben and Cathy and the bearing of Ben from Cathy?

3. Ana, Ben and Cathy are on different locations on the ground. The bearing of Ana from Ben is 40°T. The bearing of Cathy from Ana is 130°T. If the distance between Ana and Ben is 12km and the distance between Ana and Cathy is 10km, find the distance between Ben and Cathy and the bearing of Ben from Cathy?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Using double integration method (DIM), analyze the beam loaded and supported as shown: P 150KN 1.5m PIOEN 1.5 8 m a B a) Determine the value of the maximum deflection in the beam shown above. b) Determine the angle of rotation on the point 4 meters from the left support of the beam. c) Determine the location of the maximum deflection of the beam.
Determine the deflection at the end of the overhang by applying the second moment area theorem. The modulus of elasticity is 50000OMPA and the cross section is given below. See figure 10. 75mm 20KN B A 1.5m V 1.5m 120 E 2m 2m mm Figure 10 0.0021667m 0.0031667m 0.0051667m 0.0041667m
PROBLEM 1 Solve the slope and deflection at points A and B using the Moment-Area Method. Point B is at 2m from point A. 10kN/m A B E = 200GPa 25kN/m C 8m 1 = 7.5 x 10-6 m4 10kN/m
For the overhanging beam shown, determine the value of Eli0 at point C. Use Virtual Work Method. 1200 N/m 3600 N/m B A C 4 m 2 m
Using MOMENT-AREA Method for deflection analyze the beam below 25KN 10KN/m A El=120000KNM^2 El=200000KNM^2 4m 4m Solve for the Slope and Deflection at POINT B HIGHLIGHT YOUR FINAL ANSWER (PUT A BOX ON YOUR FINAL ANSWER)
Example 2. A vertical angle of -15 35' is measured to the top of a flagpole from an instrument set up on a rolling hill with an inclined distance of 625,45 meters away from it. The instrument is 1.45 m above the ground whose elevation is 520.15 m above mean sea level. If the height of the flagpole is 8 meters, find: a). Horizontal distance from the instrument to the base of the pole b).the elevation of the base.
Use Virtual Work method to solve for the slope at joint F, horizontal deflection at joint at F, and vertical deflection at joint E of the rigid frame shown. 80 KN 3m D 2m E 21 2m I 3m 30KN B21 3m 20KN OF = 1122.5kN.m?/El Ay = 4437.5kN.m³/El (at E) %3D Answer: AH = 1519.17kN.m³/El (at F)
Using Double Integration Method for the deflection of beams analyze the given structure below. 12KN/m 25KN A В -4m 5m 2m + 2m SOLVE for the SLOPE and DEFLECTION under the 25KN concentrated load
A wire makes angles of 35° and 55° at support A and B, respectively, as shown. If the wire has a mass per length of 0.5 kg/m, 1) Derive and solve the differential cquation of the shape of the wire. 2) Determine the location of the lowest point C of the wire relative to A. 3) Determine the vertical distance between the points A and B. 4) Determine the length of the wire. 55° 35° C 40 m
Using Double Integration Method for the deflection of beams analyze the given structure below. 12KN/m 25KN A C 4m 5m + 2m-2m- SOLVE for the SLOPES at POINT B
PROBLEM 3: A stadia rod held at a distant point B is sighted by an instrument setup at A. The upper and lower stadia hair reading was observed as 1.300m and 0.900m, respectively. If the stadia interval factor is 100, and the stadia constant is zero, determine the length of the line AB.
Problem 34: Determine the maximum slope and maximum deflection for the beam shown in figure by conjugate beam method. A 1.8m 50kN C 3.6m, I 10kN/m ܩܩܘܩܒ B