3. A steel bolt through a 30-in long aluminum tube has the nut turned on until it just touches the end of the tube. No stress is introduced on the bolt or the tube. The temperature of the assembly is raised from 70 to 81 degrees Fahrenheit. The cross-sectional area of the bolt is 0.09 sq. inch and the cross-sectional area of the tube of 0.30 sq. inch.

3. A steel bolt through a 30-in long aluminum tube has the nut turned on until it just touches the end of the tube. No stress is introduced on the bolt or the tube. The temperature of the assembly is raised from 70 to 81 degrees Fahrenheit. The cross-sectional area of the bolt is 0.09 sq. inch and the cross-sectional area of the tube of 0.30 sq. inch.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. A steel bolt through a 31-in long aluminum tube has the nut turned on until it just touches the end of the tube. No stress is introduced on the bolt or the tube. The temperature of the assembly is raised from 70 to 81 degrees Fahrenheit. The cross-sectional area of the bolt is 0.09 sq. inch and the cross-sectional area of the tube of 0.30 sq. inch. a. Find the thermal deformation (in inches) of the steel bolt. (Write your answer to 6-decimal places.) b. Find the thermal deformation (in inches) of the aluminum tube. (Write your answer to 6-decimal places.) c. Find the stress (in psi) induced in the steel bolt by the temperature change. d. Find the stress (in psi) induced in the aluminum tube by the temperature change.
A rigid beam rest on two bronze bars 700mm long. Another aluminum bar is placed between them which is 699.93mm long. If the weight of the beam is 375KN, determine the stress in the aluminum bar in MPa. (Round your answer to 3 decimal places) (Exclude your unit in the answer box) Bronze Alum 850 1500 Ain mm E in GPa 70 83 bronz alum bronze
Q2) A brass sleeve S is fitted over a steel bolt B (see figure), and the nut is tightened until it is just snug( no initial stresses). The bolt has a diameter dg = 20 mm, and the sleeve has inside and outside diameters dl = 21 mm and d2 = 31 mm, respectively. if the temperature drops by 100 C Calculate stresses induced in bolt and sleeve. What is the total shortening in the bolt -sleeve assembly . Derive any formula you need (Use material properties as follows: for the sleeve, as = 21 x 106/°C and Es= 100 GPa; for the bolt, ag = 10 x 10/°C and Eg = 200 GPa. d2 di dB Sleeve (S) Bolt (B)
Fagure O 2. A steel rod of 20 mm diameter passes centrally through a copper tube 40 mm external diameter and 30 mm internal diameter. The lube is closed at cach end by rigid plates of negligible thickness. The nuts are tightened lightly home on the projected parts of the rod. If the temperature of the assembly is raised by 60 "C, calculate the stresses developed in copper and steel. Take E for steel and copper as 200 GN/m and 100 GN/m and a for steel and copper as 12 10 per "C and 18 x 10" per "C. stress is the middle
20 mm 10 mm 10 mm 20 mm 10 mm 10 mm The Aluminum machine part is subjected to a bending moment M = 75 N.m. Determine (a) distance of neutral axis from the bottom of the cross section, (b) moment of inertia of the cross section about the neutral axis, (c) maximum stress at point B, and (d) maximum stress at point C. 10 mm M-75 N-m 40 mm
*7-88. Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while the glass stays approximately rigid. Determine the average shear strain in the nylon due to the load P when the assembly deforms as indicated. 2 mm 3 mm 5 mm 3 mm 5 mm 3 mm
3- Determine: m 0.4m a) The stresses in the bars shown after a temperature rise of 96°C. Brone har Ahunknan bar A-1500man A-1500mm E-10SGPa E-TGP -21.6 21 b) the corresponding change in the length of the bronze bar.
Q.2 Three bars each made of different materials are Steel Copper Ecu- 120 GPa ag = 12(10-)/C a = 21(10-")/"C a = 17(10-)C Acu = 515 mm? Brass connected together and placed between two E= 200 GPa E= 100 GPa walls when the temperature is T1 = 12°C. %3D Detemine the force exerted on the rigid A = 200 mm? Ape- 450 mm supports when the temperature becomes T2 %3D 18°C. The material properties and cross- 300 mm 200 mm 100 mm sectional area of each bar are given in the figure. (Marks = 10, CLO 3)
Hi. PLEASE ANSWER IT ASAP FOR AN UPVOTE. I NEED IT ASAP. Thank you. >>>Strength of Materials
7. ASTM suggests a tolerance of... percent to allow the variation in strength as a test of ....w. water. A. 12 В. 8 C. 10 D. 15 E. 16 F. None of them
A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1). Thesteel [E = 29,000 ksi; a = 6.5×10-6/°F] bolts have a diameter of 0.60 in. The polymer [E = 370 ksi; a = 39.6x 10-6/°F] cylinder has an outside diameter of 6.5 in. and a wall thickness of 0.35 in. Assumea = 23 in. and b= 29 in. If the termperature of this assembly changes by AT = 120°F, determine: (a) the normal stress in the polymer cylinder. (b) the normal strain in the polymer cylinder. (c) the normal strain in the steel bolts. (1) (2) (1) b Answer: (a) 02 = psi. (b) E2 = (c) E1 =
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. Aluminum 3P Bronze Steel 2P P 4P - 1.0 m- - 0.6 m→- ste-0.8 m - A (mm²) E (GPa) . (MPa) Bronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140