3. A biological signal, x-(t), which has a bandwidth of 2kHz has been sampled with using Fs = 8kHz sampling frequency; x(n). a) Draw all steps of the sampling process. b) The signal x(n) has been decimated with the highest possible lossless sub-sampling rate M and the signal xa(n) has been obtained. Draw all steps of the decimation process. X-(Q) Ω -Qm QM

3. A biological signal, x-(t), which has a bandwidth of 2kHz has been sampled with using Fs = 8kHz sampling frequency; x(n). a) Draw all steps of the sampling process. b) The signal x(n) has been decimated with the highest possible lossless sub-sampling rate M and the signal xa(n) has been obtained. Draw all steps of the decimation process. X-(Q) Ω -Qm QM

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. a) Sketch the spectrum of the message signal x, (t) =4 sinc(2f) cos(6tt) and then find bandwidth and minimum sampling frequency. ninin b) The signal x, (t) is time division multiplexed with the signal whose spectrum is given in Figure 1(a). Prior to multiplexing, both signals are sampled separately. If the sampling of the both signals will be done with same minimum frequency, then how the sampling frequency should be selected? X2(f) -2.5 f(Hz) 2.5 Figure 1(a)
Computer Science You want to get a system to generate a double lateral band modulated signal without suppression, modulation index= 20% and the central frequency=50MHz, The signal has a bandwidth of 4MHz, and the spectral starts at 500 Hz. A) Find the amplitude of the bias B) Whats the bandwidth of the modulated signal?
If the signal to be analyzed is an analog signal, then we pass the signal to an antialiasing filter where B is the bandwidth of the filtered signal. What sampling frequency (Fs) should be used to make this signal discrete/digital?
-B M(f) B m(t) is a low-pass signal with B=1kHz. Using ideal filters and SSB (with upper side band) we modulate the signal at 100 kHz. In which frequency spectrum the modulated signal has power. a. Between 99 kHz and 101 kHz O b. Between 99 kHz and 100kHz ○ c. Between 100 kHz and 101 kHz d. Between 98 kHz and 102kHz O e. Between 100 kHz and 102kHz
What is the relationship between the analog signal frequency F and the digital signal frequency f? (T is the period of the sampling period)a. F = f * Tb. F = F * Tc. No connectiond. Nothing is right
Compute the eight-point DFT of the sequence x(n) using radix-2 decimation-in-time. Follow exactly the corresponding signal flow graphs and keep track of all the intermediate quantities by putting them on the diagram. x(n)=1/2.sin(pie/4.n),0<=n<=?
DIGITAL COMMUNICATIONS H.W. Q1/ A) Find the sampling frequency for the following signals: 1) S1 = 20 cos(1500nt) * cos (4000nt) 2) S2 = sin (200xt. 3) S3 = sin4000nt + 5 cos(1200nt) nt B) The following waveform is the RB (return to bios) representation of the serial digital data, find the digital data code and draw the NRZ (non-return to zero) and RZ (return to zero) waveforms. C) waveform below is the PAM for the analog signal, draw the analog signal, PWM and the PPM for this signal. 02/ The following data stream (10011011 11001110 11110000 10001000 11100000 11011010 11111111 01110111 10011001 11100111 01011010) will be transmitted with signaling rate equal to 80 k bit/sec. 1- Find the data transmitted using L- parity, V- parity and L&V parity. 2- Find the Hamming code of the last byte of the data only in which two error can be detected and one error can be corrected, calculate the transmitted bandwidth? how can reduce the transmitted bandwidth? Explain and calculate the reduced…
Consider the following continous time signal x(t). Assume that the signal was sampled at a sampling frequency of 20 Hz. Plot the magnitude spectrum of the sampled signal as a function of cyclic frequency. Be sure to include n values of up to +-2. Label x and y axis. Did aliasing occur? If so, what is the aliased frequency? x(t) = 1 + 2cos(2pi25t)
Q1: Draw the froquency spectrum of an analog signal to be converted into a digital signal ( maximum Frequency equal to SKH2 ) if i) fs> 20% from nyquist frequency. il) fs < 20% from nyquist frequency. ili) s- 20% from nyquist froquency aluin one of its
7-18 Abasehand signal having components from near de to 8 kHz is used to frequency modulate a high-frequency carrier, and the maximum frequency deviation is set al +12 kHz. Delermine the approximatle transmission bandwidth.
If the signal x(t)= cos(2*pi*40t) is sampled with a sampling frequency of 20 Hz, what signal will be produced?a. cos(pi * n)b. cos(2*pi*n)c. cos(4 * pi * n)d. cos(8 * pi * n)
A measurement system has noise above 20 kHz and the data signal frequency is between 100and 500 Hz. What are the resistor and capacitor values for an RC filter that will reduce the noiseby 95%, i.e., only 5% is left?