3) The rectangular tube cross-section of a beam, shown in the figure aside, is bent about a horizontal axis due to the bending moment of 899.5 Nm. Calculate the total force that is acting on the shaded portion of the cross-section of the beam. (Suggested time for solution is 25 minutes) 0.8cm 4.6cm 0.8cm 3cm 0.8cm 0.8cm

3) The rectangular tube cross-section of a beam, shown in the figure aside, is bent about a horizontal axis due to the bending moment of 899.5 Nm. Calculate the total force that is acting on the shaded portion of the cross-section of the beam. (Suggested time for solution is 25 minutes) 0.8cm 4.6cm 0.8cm 3cm 0.8cm 0.8cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A telescope with tripod weighs 25 pounds and has geometry as shown in the figure and parameter table. Its center of gravity is at G and the ground can be considered to be a smooth surface. What are the vertical support reactions at A, B, and Č G В A L2 -3 y parameter value units 4.25 ft L2 La L4 1.75 ft 2 ft 1.5 ft The normal reaction at A is lb The normal reaction at B is lb The normal reaction at C is lb
13:17 X A telescope with tripod weighs 40 pounds and has geometry as shown in the figure and parameter table. Its center of gravity is at G and the ground can be considered to be a smooth surface. What are the vertical support reactions at A, B, and C? 4₁ cc 080 2021 Cathy Zupke A wamap.org parameter L₁ L2 L3 LA G 7 B The normal reaction at A is The normal reaction at B is The normal reaction at Cis value units 4.75 2 1 1 -4₂- CY ft ft ft ft =L3 4 lb lb lb
Both wires have a cross sectional area of 17 mm2 and are constructed of the same material with a modulus of elasticity of 200,000 MPa. 1. Determine the wires' tensile stress at C. 2. Determine the wires' tensile stress at D. 3. Calculate the maximum displacement possible.
4/74 For what value M of the clockwise couple will the horizontal component A, of the pin reaction at A be zero? If a couple of that same magnitude M were applied in a counterclockwise direction, what would be the value of A,? 150 Ib 60 Problem 4/74
A prismatic bar is fastened between two rigid walls A and Band subjected to loads as shown in figure. What will be the ratio of magnitude of reaction at A and B respectively? +13.6 kN Þ27.2 kN A C D В 100 mm 200 mm 300 mm
The value of W that results in the collapse of the beam shown in the adjoining figure and having a plastic moment capacity of M, is Fixed Hinge -7m- 3m
Mechanics of Deformable Bodies Determine the maximum tensile and compressive bending stresses in the beam shown. 4 kN/m 200 mm putium, El A B 6 m 80 mm † 1= 30 x 106 mm ΝΑ
Problem 3: Referring to the two beams shown in figure STAT-003, determine the reaction at A. 600 N 1900 N 4000 N A B 6m 4m 4m 6m 4m STAT-003
Figure P24.25a shows a uniform beam subject to a linearly increasing distributed load. The equation for the re- sulting elastic curve is (see Fig. P24.25b) EI dx Note that the analytical solution for the resulting elastic curve is (see Fig. P24.25b) Wo(-x +24x -L*x) 120 EIL Use bvp4c to solve for the differential equation for the elastic curve for L 600 cm, E 50.000 kN/cm2, I 30,000 cm, and w 2.5 kN/cm. Then, plot both the numerical (points) and the analytical (lines) solutions on the same graph.
Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the figure below where the horizontal force P = 155 N and the couple M = 573 Nm. M N m A 150 N 300 mm 250 mm PN 400 mm 90 N
2: Analysis the structure shown in figure, El is constant We15 KN/m P-30 KN 4m
150 mm 60 mn 300 nm 000 m 50 mm 5 m B 25 kNm 5 m 10 KN A beam is created by nailing 3 planks together with 2 rows of nails as shown above. The beam exhibits a pin support at A and is suspended by a cable at B. A concentrated load of 10 kN is applied at the free end while a moment of 25 kNm is applied at location B. a) Determine the second moment of area (I) of the cross-section b) Draw the free body diagram, shear force diagram, and bending moment diagram of the beam c) For the maximum shear force on your SFD, determine the maximum and minimum shear stresses at the interface between the horizontal and vertical planks d) For the maximum shear force on your SFD, Determine the shear stress at the neutral axis