Refer to the figure. Given2RRL²R2 =3R2 – R_°a) Design the power supply cireuit so that vị = 3v,when R1 = 600 2.b) Assume input voltage is 180 V. Which resistor in the circuit dissipates the most power? What is the power?c) Which resistor dissipates the least power? What is the power?R:ww-RRww+ViRVoRLbdww

The given circuit is as shown below, Given, R2=2RRL23R2-RL2 We need to design the power supply…

Answered: 2RR 2 R2 = 3R² – R1² Design the power…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

the adjoining figure. This lamp can withstand a maximum voltage 3.0 v 0.4 9. Volt-ampere (V-I) charaeteristics of an incandescent lamp 16thd in and a maximum current 0.4 A. An infinite ladder network consisting a large number of these lamps is also shown in the figure given belo How much maximum voltage can be applied between the terminals A and B, so that no lamp gets damaged? (Use V5 = 2.2). Ans:x4.2V Hint: Curentin all bulls except first is
A dc generator and a battery are connected to a resistive load RL in the figure below. For each, determine the value of RL for maximum power transfer to RL. Next is to determine RL to 75% efficiency
The diagram in the figure shows a simple circuit consisting of a battery and a load consisting of two resistors.The battery voltage is UB = 56 V and the value of the resistors is:R1 = 1800R2 = 5400a) The ammeters in the circuit show the following value:A1 shows valueA2 shows valueA3 shows valueb) In the load, the effect developsc) The total resistance of the load is
Given the circuit below and that R1=1.7ohm,R2=3.5ohm,Emf1=2.1V and Emf2=6.3V. What is the current through the section ac?
R2 Q1 ... VCC R1 Show your complete solution. Use two decimal places for your final answer. Calculate the value of RC in ohms. at VCC=18 V, IB=26 uA, and VC=7V and B=69
%3D ) Drurde (l0o1102 and (o
Determine E and P3. Given R1 = 10ohms, R2 = 20ohms, R3 = 60 ohms, R4= 10ohms, R5= 20ohms, R6= 60ohms, R7= 10 ohms, R8= 20 ohms. R9= 30ohms, P6 = 540W.
Use Kirchhoff's Law to solve for the current passing through each resistor. Compare it with what you got from the PHET Simulation A D 392 www 6V E www F 192 www 292 352 www 9V B C
Which of the following statements are correct for the circuit below? Thanks to the capacitors I – C1 and C2, the voltage gain of the circuit increases. II – Capacitors C1 and C2 are coupling capacitors and provide an isolation function between AC and DC voltages in the circuit. Thanks to the III – RE resistor, the voltage gain of the circuit increases. Thanks to the IV – RE resistor, the stability of the circuit increases. The V – C3 Capacitor is a bypass capacitor and prevents the loss of voltage gain. Capacitor VI – C3 is a coupling capacitor and has no effect on the voltage gain in the circuit. VII – As the value of the source internal resistance Rs increases, the voltage gain decreases. VIII – The voltage gain decreases as the value of any RL load to be added to the circuit increases
If the voltage V, = 800 mV, then the current flowing in the load I, is: %3D -j20n Select one: O a. None of these O b. Is 100 <-90° mA O c. Is 5.0<.-90° A O d. Is 5 <90° mA ell
In an electrical circuit four resistors are connected in parallel and their equivalent resistance is 50ohms. Find the value of each resistors if the currents through each impedance are 0.8, 0.4, 0.6 and 0.2 ampere.
shfdjkfdrhnacoioeniodinopidopdnieocmixoxwmipdf.ziudSALIDUDetu The equivalent resistance of three resistors A, B and C connected in parallel is 1.5 ohms. If A is thrice of B and C is 1/4 of B. Find the equivalent resistance when the three of them are connected in series? dhffrriru9ee

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

2RR 2 R2 = 3R² – R1² Design the power supply circuit so that vị = 3v,when R1 = 600 Q. Assume input voltage is 180 V. Which resistor in the circuit dissipates the most power? What is the power? Which resistor dissipates the least power? What is the power?