2C. For the T-beam shown, determine the centroid of the beam and the second moment of inertia about the horizontal centroidal axis. Will the second moment of inertia about the x-axis (lx) be larger, equal to or smaller that the ly value? |Ye= Ix > ly in in 1x = ly 1 in A 3.5 in I, < ly 8 in in4 1 in 8 in (Circle One)

2C. For the T-beam shown, determine the centroid of the beam and the second moment of inertia about the horizontal centroidal axis. Will the second moment of inertia about the x-axis (lx) be larger, equal to or smaller that the ly value? |Ye= Ix > ly in in 1x = ly 1 in A 3.5 in I, < ly 8 in in4 1 in 8 in (Circle One)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The left support of a fixed beam having length 3m is rotated by 0.001 radian in the anticlockwise order, Take El = 2 x 1013 Nmm². FEM generated at right support is hogging moment of 20 kN.m sagging moment of 10 kN.m hogging moment of 10 kN.m Osagging moment of 20 kN.m
The left support of a fixed beam having length 3m is rotated by 0.001 radian in the anticlockwise order, Take El = 2 x 1013 Nmm². FEM generated at right support is hogging moment of 20 kN.m sagging moment of 10 kN.m sagging moment of 20 kN.m O hogging moment of 10 kN.m
Determine the second moments with respect to x- (hori zontal) and y- (vertical) axes through the centroid of 36 21 21 mm 21 21 mm mm mm
Before the load P was applied, a gap, ?0 existed between the cantilever beam AC andthe support at B. Knowing that E=200 GPa, determine the magnitude of P for which thedeflection at C is δ and the reaction at B (Hint: Use the method of superposition and beam deflections in Appendix A) ?0 (mm)=2.75 δ (mm)=5.5
1. Two cylindrical rods, CD made of steel (E = 29 Msi) and AC made of aluminum (E = 10.4 Msi), are joined at C and restrained by rigid supports at A and D. Determine (a) the reactions at A and D, and (b) the deflection of point C. 8 in. A 10 in. 18 kips 1-in. diameter 10 in. 14 kips 1-in. diameter
Q1: It is required that the resultant force acting on the evebolt in the Figure to be directed along the positive x axis and that F2 have a minimum magnitude. Determine this magnitude, the angle 0, and the corresponding resultant force. F, - 800 N 60 F2
Force P with 5.05 kN magnitude acts along the parallelepipeds diagonal CE, pointing towards E 290 mm 290 mm 145 mm Determine the magnitude of the moment of Pabout the following Ines in N-m. (a) Ine OA N-m (b) ine O8 N- m (c) Ine AB N-m (d) Ine BF N-m (e) ine BG N-m (r) Ine DG N-m (a) Ine 0D N-m (h) Ine OC N-m (1) ine EF N-m (1) Ine OF
DETERMINE THE EXTERNAL REACTIONS AT FIXED SUPPORT AND SLOPE AND DEFLECTION AT MIDSPAN OF SEGMENT BC OF THE BEAM SHOWN USING CONJUGATE BEAM METHOD
Determine the location of the GEOMETRIC CENTROID and PLASTIC CENTROID. Use fc' = 27.6 MPa and fy = 414 MPa (3) T 350 150 dpe 300 3N28 2N28 + 500 330 -455 145
The motion of pin P is guided by slots cut in rods AD and BE. Knowing that bar AD has a constant angular velocity of 4 rad/s clockwise and bar BE has an angular velocity of 5 rad/s counter-clockwise and is slowing down at a rate of 2 rad/s², determine the velocity(m/s) of P for the position shown. P 150 mm 150 mm B A Select the correct response(s): 3.36 4.32 2.26 6.22 7.71 5.42 00000 100 mm 300 mm
03 In Fig. P4-03 the electric motor exerts a torque of 3,000 N.m on the steel shaft ABCD when it is rotating at constant speed. If the torques at B and C are as shown, det- ermine the total angle of twist between points A and D. For steel, G = 79 GPa. 1,800 N.m 1,200 N.m Electric motor d=64 mm G 0.25 m d=50 mm 0.30 m d=38) mm 0.20 m
QI/ The rigid pole and cross-arm assembly is supported by the three cables shown. A turnbuckle at D is tightened until it induces a tension T in CD of 1.2 kN. Express T as a vector. Does it make any difference in the result which coordinate system is used? Ans. T = 0.321i + 0.641j – 0.962k kN, IC 1.5 m B 1.5 m G T= 1.2 kN 3 m 2 m 1.5m 3 m