For checking, answer number 2 show solutions. 1. Fluid is moving at rate of 3m/s ina chamber of a 12inch positivedisplacement flow meter, if thedensity of the fluid is 4.5kg/m³and has a mass flow rate of 8kg/s,what is the maximum volumecapacity of the chamber?2. A cube block of ice with a volumeof 244 ft³ with an initialtemperature of 28 °F is 12ft neara furnace with an ambienttemperature of 186 °F. If thethermal conductivity is 0.15BTU/hft°F, what is amount of heat lossby the ice?

Name: For checking, answer number 2 show solutions. 1. Fluid is moving at ra
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: For checking, answer number 2 show solutions. 1. Fluid is moving at rate of 3m/s ina chamber of a 12inch positivedisplacement flow meter, if thedensity of the fluid is 4.5kg/m³and has a mass flow rate of 8kg/s,what is the maximum volumecapacity of th

According to Bartleby guideline, we can answer only one question at a time. You are requested to…

Answered: 244 ft³ with mperature of urnace with…

Engineering

Mechanical Engineering

244 ft³ with mperature of urnace with ire of ono

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Container is placed 55 cm from the ground contains fluid with density of 757 kg/m3 and dynamic viscosity of 1.35x105 Ns/m2. The fluid moving in pipe on ground with 0.15mm roughness, 4200 cm long, and 4 mm radius before being dismissed to atmosphere. i. Find mass flow rate of the fluid.
Chlorine gas enters a 30-mm ID pipe at 15 m/s, and exits a wider pipe, at 85-mm ID. What is the average velocity through the exit pipe (in m/s)?
y aer. A Pitot tube is used to measure the air flow rate in a eircular duct 8.5 m I.D. The "riowing air temperature is 65.5°C. The Pitot tube is placed at the center of the duct and the reading R on the manometer is 1.2 cm of water. A static pressure measurement obtained at the Pitot tube position is 2.0 cm of water above atmospheric. Take Cp 0.98,9ter ase press u = 2.03 x 10 Pa.s, if U- Ux ( 1-0.17). Calculate The velocity at the center and the average velocity. The volumetric flow rate of the flowing air in the duct
Answer with True or False of the following question: (7M 1. Water flows steadily down a vertical pipe of constant cross section. Neglecting friction, according to Bernoulli's equation, velocity decreases with height. 2. A liquid in an open right circular cylinder is given rigid body rotation about the axis of the cylinder. The pressure distribution in any vertical plane is uniform. 3. A curved surface is submerged in a static liquid. The horizontal component of pressure force on it is equal to the pressure force on a vertical projection of the surface. 4. A U-tube manometer measures the difference in total energy between two points.
1. A tank is filled with air at a gauge pressure of 6 bar and 55 °C, determine the specific weight of the air in the tank. True changing with time. Non-wo... AURREREAN ly 6. A Venturimeter having inlet diameter 1.8 cm and throat diameter 0.5 cm. The oil-mercury differential manometer has a reading of 5 cm. Calculate the discharge of an oil of SG=0.9.
Q.1. A large tank contains air, gasoline (pc= 680 kg/m³), light oil (p= 800 kg/m³) and water. The pressure p of the air is 150 kPa gauge. If we neglect friction, what is the mass flow rate of oil from a 20- mm-diameter jet? 1₁-2m Air Gasoline 8G Water- 90 Oil.. d. 20 mm #i 2-3m
1-In-compressible fluid flow in pipe line, there are two kinds...... a- Transition & turbulent flow c- laminar & turbulent flow. b- laminar & Transition flow. d- Other. 2- The viscosity actually a is the resistance of the internal material movement and that because of..... ...between molecules. a- the cohesion forces. b- Buoyancy force. c- the adhesion forces. d-Other. 3- calculate the surface tension of liquids and solutions using the following mathematical relationship: ******** a-Y-0.5h+p-g/r. b-Y-0.5 h pgr. c-Y-(h* p*g*r)*5. d-Other.
Q.1 The force in (newton) required to lift a thin wire ring of diameter 2cm from a water surface of given surface tension at 21 C is 2N/cm A 9Tt В C D
1. The deformation of the fluid will continue as long as the 2. When designing gates, vessels, dams or other bodies that are submerged in a liquid, it is important not only to estimate the - 3. The surface tension is the tensile force per -- in any direction along the surface the surface tension. 4. The value of - specifies whether the fluid can be assumed compressible or incompressible. 5. Archimedes' principle indicates- 6. A truck is filled with gasoline. If the container (tank) on the truck undergoes a - - is applied. - but also to specify its location on the body. then the liquid surface will begin to rotate clockwise about the center of the container and will eventually maintain a fixed tilted position.
A/ in a static fluid, with y as the vertical direction, the pressure variation is given by:
Q,; A liquid of (u =1.25 Pas.) fills the space of (Smm) shown in figure below. Calculate the forque (T) required to rotate the frustum cone at constant Speed of (60 rip.un). o. 3m a.7m
1. The deformation of the fluid will continue as long as the 2. When designing gates, vessels, dams or other bodies that are submerged in a liquid, it is important not only to estimate the - 3. The surface tension is the tensile force per --- in any direction along the surface the surface tension. 4. The value of --- specifies whether the fluid can be assumed compressible or incompressible. 5. Archimedes' principle indicates --- 6. A truck is filled with gasoline. Ifr the container (tank) on the truck undergoes a - , then the liquid is applied. --- but also to specify its location on the body. surface will begin to rotate clockwise about the center of the container and will eventually maintain a fixed tilted position.