221. According to Figure Q21, which Gauss's Law procedures stated below were violated? a. The surface is chosen such that D is normal or tangential to the surface. b. When D is normal to the surface, DodS = D dS because D is constant on the surface. c.) When D is tangential to the surface, D-dS = 0. d. Choose a surface that has some of the symmetric exhibited by the charge distribution. e. I don't see any procedure is violated in this case. Gaussian surface XX 2m a. Decrease b. Increase c. Reduce to zero d. Remain unchanged 1m infinite sheet of charge Figure Q21 Q22. When a dielectric is placed in an electric field, the electric field strength will:

221. According to Figure Q21, which Gauss's Law procedures stated below were violated? a. The surface is chosen such that D is normal or tangential to the surface. b. When D is normal to the surface, DodS = D dS because D is constant on the surface. c.) When D is tangential to the surface, D-dS = 0. d. Choose a surface that has some of the symmetric exhibited by the charge distribution. e. I don't see any procedure is violated in this case. Gaussian surface XX 2m a. Decrease b. Increase c. Reduce to zero d. Remain unchanged 1m infinite sheet of charge Figure Q21 Q22. When a dielectric is placed in an electric field, the electric field strength will:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A solenoid displaces a material plunger ferromagnetic at a distance of 1 cm. The inductance of the solenoid in function of the position of the plunger is given by: L(x) = 0,05 – 20000((r - xo)) H, where x ranges from 0 to 0.01 m and xo = 0.25 m Is there a point where the force generated in the plunger is zero? If so, for what value of x?
1. Inductance. Consider the configuration of a wire with 90° bends as shown below. A small loop, with its sides of length a and width d = a/16 is placed with its plane lying along xz principal plane as shown. Stating all assumptions, determine mutual inductance between the loop and the wire. a/2 9/2 2a
A solenoid displaces a material plunger ferromagnetic at a distance of 1 cm. The inductance of the solenoid in function of the position of the plunger is given by: L(x) = 0,05 – 20000((x – xo)) H, where x ranges from 0 to 0.01 m and xo = 0.25 m Determine the direction of the force generated in the plunger (same direction of x or in the opposite direction?), the point where the force is zero (if it exists) and the maximum force generated for a current of 1 A
Q14. An air filled parallel plate capacitor is arranged such that the upper plate carries surface charge density 2C/m² and lower plate carries surface charge density -2C/m² as shown in figure. The electric field intensity under the bottom plate will be
An infinitely long straight wire carries 1000 A of current and in the vicinity, there is a circular conducting loop of 100 mm diameter with the center of the loop 1m away from the straight conductor. Both the wire and the loop are coplanar. The magnitude and direction of current in the loop that produces a zero flux density at its center is?
The figure is a cross section through three long wires with linear mass density 58.0 g/m. They each carry equal currents in the directions shown. The lower two wires are 4.0 cm apart and are attached to a table. What current I will allow the upper wire to "float" so as to form an equilateral triangle with the lower wires?
Q5. Consider two magnetic fields given by (a)B = 3x²y – 4xz + 5z2 and (b) B =constant. Comment on these magnetic fields.
The figure below is a top down view of a circular wire coil with rotating clockwise in a uniform magnetic field directed to the right. The position of the wire at t=to is shown as dotted lines, the position of the coil t=t is shown as a solid line. to- A t - a) Label the direction of the induced current at points A and B. b) Is the magnitude of the induced current increasing, decreasing, or constant as it moves from its position at to to t? (Tip: is the loop position headed towardI 0 or l Imax at t = t?) c) Label the direction of the force on the wire at points A and B. d) Will the torque on the wire speed up or slow down the angular velocity () of the wire? B.
current caming loop with radins =m and %3D P5 For a current I = 2A find the moyentic flux density at %3D Point (P)on the Z-axis when r=lm (where ris the distanu from(P) to Me any Paint on the conductor ( loop) and the Conductor is placed plane). Also find the mogneticflex density when (P) is at the centeraf the loop. on the hovizontal
A cylindrical long solenoid of length 2000 mm has 20 mm diameter. If number of turns wounded on solenoid is 2000 turns what is value of inductance.
1. ELECTRIC FLUX. A rectangular flat surface with sides 0.200 m and 0.500 m is under the influence of a uniform electric field E = 85.0 Nc that is directed at 20.0° from the plane of the rectangular sheet. Find %3D the electric flux through the rectangular flat sheet.
This problem is complete the question with proper dimension of rectangular plate. can u assumtion please Please solve max in 20-25 please the subparts A,B,C Im very needed a solution and send thank u A plate plate in a vacuum, has a rectangular area whose sides are 20 cm long. The distance between the two plates is 5 mm. So, A. Make a summary and calculate the value of the capacitance! B. If there is a dielectric material with dielectric constant k = 2 having dimensions of 20 cm x 10 cm x 5 mm is placed between the two plates, then sketch the trainer and calculate the current capacitance value? C. If there is a dielectric material with dielectric constant k = 4 , having dimensions of 20 cm x 10 cm x 2 mm is added to the condition of problem B) and is placed in the blank between the two plates, so that it sticks to one of the plates. So make a sketch of the sport and determine its current capacitance value?