2. Two different transformers details are tabulated helow. Calculate the missed values in the table. Secondary terminal voltage of the second transformer is 487.5V when loaded. Determine the regulation of the transformer. N, | N v, | L(60000 VA SOH2) ? 100 1.6KV 100v:? ? 25cm v, 1 1 Transformer Flux Area IL.(6000VA SOHZ 100 100 500 ?0.04505Wb flux density 1.50T)

2. Two different transformers details are tabulated helow. Calculate the missed values in the table. Secondary terminal voltage of the second transformer is 487.5V when loaded. Determine the regulation of the transformer. N, | N v, | L(60000 VA SOH2) ? 100 1.6KV 100v:? ? 25cm v, 1 1 Transformer Flux Area IL.(6000VA SOHZ 100 100 500 ?0.04505Wb flux density 1.50T)

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter4: Symbols

Section: Chapter Questions

Problem 7SQ: The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d....

See similar textbooks

Similar questions

A single-phase step-down transformer is rated 13MVA,66kV/11.5kV. With the 11.5 kV winding short-circuited, rated current flows when the voltage applied to the primary is 5.5 kV. The power input is read as 100 kW. Determine Req1andXeq1 in ohms referred to the high-voltage winding.
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
The direct electrical connection of the windings allows transient over voltages to pass through the auto transfonner more easily, and that is an important disadvantage of the autotransformer. (a) True (b) False
In small transformers, the total copper loss may vary from the rated output. % of O 0.2 to 0.6 O 0.5 to 1 O 0.8 to 1.5 O 0.4 to 1
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
With base MVA of 150 and base voltage of 33. If the reactance of the transformer is 0.23 pu. The parameter of the reactance of the transformer in the Neplan software is O 1.66 2.30 23 0.23 O Non of them
The ratings of a single-phase three-winding transformer are as follows:*primary winding: 300 MVA, 14kV*secondary winding: 300MVA, 200kV*tertiary winding: 40MVA, 20kV. The leakage reactances are:*Xps = 0.1 at 300MVA, 14kV*Xpt = 0.16 at 40MVA, 14kV*Xst = 0.14 at 50MVA, 200kV Neglecting the winding resistance and exciting current, calculate Xp, Xs and Xt using 300 MVA and 14kV as the base for the primary winding.
It is desired to have a 4.13 mWb maximum core flux in a transformer at 110V and 50 Hz. Determine the required number of turns in the primary.
In the single-phase, three- winding, transformer, the primary current is equal to lo at the condition of ints there is no load on tertiary windings the current in secondary windings equal to zero the resistances (R1, R2, and R3) in transformer windings are equal the inductances (L1, L2, and L3) in transformer windings are equal.
In a buck converter, what are the benefits and disadvantages if the changes of duty cycle is drastic i.e, fast system response? How about when duty cycle changes slowly i.e, slow system response?
Help me to solve the average current, peak current, transformer
What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer? O a. Both are unequal and in phase O b. Both are unequal and 180 degree out of phase O c. Both are equal and 180 degree out of phase O d. Both are equal and inphase