2. The sequence b(k) = {1, 1, 0, 1, 0, 1} is transmitted at bit rate of Rp =200 b/s using an ASK digital system. The carrier signal c(t) is 1.5 cycle/Ts, determine the following; a- Calculate the carrier frequency f c. b- Calculate the bit duration T, and the required bandwidth BASK:

2. The sequence b(k) = {1, 1, 0, 1, 0, 1} is transmitted at bit rate of Rp =200 b/s using an ASK digital system. The carrier signal c(t) is 1.5 cycle/Ts, determine the following; a- Calculate the carrier frequency f c. b- Calculate the bit duration T, and the required bandwidth BASK:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The transmitted bit stream consists of 25 bits of repeating (arrow to theleft) 11000 and the transmission bit rate is 600 bits/second using ASKwith the 5V, 1800 Hz carrier. (a) Determine the fundamental frequencyrange of the transmitted ASK signal. (b) If the ASK signal is transmitted ona noiseless channel with a bandwidth of 1200Hz. Determine the peakamplitude of the received ASK signal. Answer this item in this format:
3. In an FM signal that modulating frequency is a 1.5-kHz sine wave. The carrier frequency is 1000 kHz. The frequencies of the third significant sidebands are ___ and ___ kHz.
q6- Consider an Orthogonal frequency-division multiplexing data transmission mode of bandwidth 60 KHz with a cyclic prefix of 33 samples. There are 120 carriers used for data transmission, the outer 30 carriers are used for reducing adjacent channel interference, and 10 carriers are the pilot symbols. Calculate the symbol time for the raw OFDM in (milli second) Select one option: a. 5 b. 3 c. 1 d. 2
Q24)This multiple choice question from DIGITAL COMMUNICATIONS course.just write for me the final answer. The choice of the number of bits per PCM word depends on the a. SNR b. Bandwidth c. None of the mentioned d. SNR and bandwidth
Complete the following sentences:1. A rectangular pulse with a pulse duration , so in frequencydomain its form will be ………… 2. When the modulation index is (1) means that the amplitude of the message signal is ……… the amplitude of the carrier signal.
Explain frequency hopping acquisition scheme using a simple PN sequence. Assume that the length of PN sequence is 15 and the number of frequency hopping levels is 8
A 450 kHz carrier signal is modulated with a 15 kHz modulating signal. What are its sideband frequencies?
To create a Pseudo Noise code of length 15 bits, how many shift registers are required? Techniques used in Wideband Modulation are: 1. Direct Sequence Spread Spectrum 2. Orthogonal frequency Division Multiplexing 3. 1 & 2 4. Frequency Hopping 5. 1, 2, &3
Problem 4: A leased telephone line of bandwidth 4 kHz is used to transmit binary data. Calculate the data rate (in bits per second) that can be transmitted if we use: a. Polar signal with Manchester (split-phase, twinned-binary) pulses. b. On-off signal with rectangular half-width (RZ) pulses.
The word "carrier shift" is frequently misunderstood or misinterpreted. Carrier shift is also known as upward or downward modulation and has nothing to do with the carrier's frequency. When the positive and negative alternations in an AM modulated signal are not equal, carrier shift occurs. Which of the statements below is TRUE? Select your answer. Positive carrier shift occurs when the modulated signal's positive alternation has a greater amplitude and modulation index than the negative alternation. Positive carrier shift occurs when the positive alternation of the modulated signal has a greater or equal amplitude than the negative alternation. Negative carrier shift occurs when the modulated signal's negative alternation has a greater or equal amplitude and modulation index than the positive alternation. Negative carrier shift occurs when the modulated signal's negative alternation has a greater amplitude than the positive alternation.
Don't need to elaborate the answer. Just write down the correct answer. Some questions may have multiple answers. 1) Which multiplexing technique shifts each signal to a different carrier frequency? a) FDM b) TDM c) WDM d) PDM 2) Which multiplexing technique involves signals composed of light beams? a) FDM b) TDM c) WDM d) PDM 3) We need an addressing mechanism in a) Satic b) Parallel c) Synchronous d) Statistical 4) Pulse stuffing is a strategy used in a) TDM b) FDM c) FHSS d) WDM 5) a) FDM b) TDM technique uses multiple carrier frequencies. c) WDM d) FHSS e) DSSS TDM. 6) We need to use synchronous TDM and combine 20 digital sources, each of 100 Kbps. Each output slot carries 1 bit from each digital source, but one extra bit is added to each frame for synchronization. Answer the following questions: i) What is the size of an output frame in bits? a) 10 b) 20 c) 21 d) 11 ii) What is the output frame rate? a) 200000 frames/sec b) 210000 frames/sec c) 10000 frames/sec d) 100000…
Please help me with my homework. Thanks! The course subject is Fundamentals of Electronic Communications. 2. A 75 MHz carrier having an amplitude of 50 V is modulated by a 3 KHz audio signal having an amplitude of 20 V. Determine the modulation index, % modulation, fusb, flsb, AM equation.