2. The diameter of the discharge pipe of a pump is 15 cm and that of the intake pipe is 20 cm. The pressure gage at the discharge reads 207 kPa, and the vacuum gage at the intake reads 25.4 cm. liters Hg. If Q = 85 discharge are of the same elevation. of water and the Brake Power is 35.0, find the efficiency. The intake and sec

2. The diameter of the discharge pipe of a pump is 15 cm and that of the intake pipe is 20 cm. The pressure gage at the discharge reads 207 kPa, and the vacuum gage at the intake reads 25.4 cm. liters Hg. If Q = 85 discharge are of the same elevation. of water and the Brake Power is 35.0, find the efficiency. The intake and sec

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1: Find the pump efficiency if the pressure difference across the pump is 230 kPa. If the outlet 2₁ 14 cm Z2 diameter of the pump is 7 cm, the inlet diameter is twice the outlet diameter. take the mass flow = 50 rate of the pump is equal to 50 kg/s 72. 1 Wate C the pump nmotor = 85 % Motor 20 W
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate: a) the pump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) thepump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
Not yet answered سؤال 1 Marked out of 100.00 A closed reservoir filled by water, is under the pressure of 49 KPa as shown in the Fig.1. find the velocity of water (V) which leaves the reservoir. P=49 KPa 3m Fig.1
A pump delivers 20 cfm of water having a density of 62 lbs. per cubic foot. The suction anddischarge gage reads 5 inches Hg vacuum and 30 psi respectively. The discharge gage is 5 ft abovethe suction gage. If pump efficiency is 70%, what is the motor power?
Include a free body diagram A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. A. 12.74 m B. -4.67 m C. 2.56 D. -2.72 m
Q1/ A) An impulse wheel is to be designed to develop at the nozzle pressure is 40 kg/cm and the deflect the jet impinging on them 150°. The center line of the bucket is on a circle of 250 cm find:- 1. The speed of the Pelton wheel (rpm). 2. Efficiency and hours power the theoretical, at the nozzle flow rate 3 m'/sec. 3. Specific speed.
A petrolengine has mechanical efficiency 0.8 and lower calorific value of ispoots 44.2 MJ/kg. The engine bore 0.06 m and stroke of 0.08 m. The engine speed of 2000 rom. The consumption of fuel about 8 liter/h and the brake welght is 200N. Take the density of fuel as 750 kg Im3 and torque arm of A00 mm Find the specific fuel consumption.
A pumps delivers 1.6m³/min if water at 20°C against a pressure of 287 kpa. kinetic and potential energy changes are negligible. If the driving motor supplies 10 kW, what is the overall efficiency?
Liquid water is flowing at a rate of 25 gpm in a pipe. At one end of the pipe, the internal diameter is 2-in and the gauge pressure is 10psig, and at the discharge end 20ft away horizontally, the water discharges into the atmosphere through a 3.5-in ID pipe. Find the friction in ft of water.
A pump draws 20 L/s of water from reservoir A to reservoir B. Assuming f = 0.013 for all pipes, compute the horsepower delivered by the pump. Pump elevation is at datum.Data as follows: Reservoir A to pump. L= 500 m, D = 200 mm, EL. = 15 m Pump to Reservoir B L= 1200 m, D = 150 mm, EL. = 60 m
A centrifugal pump delivers 60 litres of water per second to a tank situated at a height of 20 metres. If the overall efficieney of the pump is 70%, find the power required for the pump. (Ans. 16-8 kW) 1.